SFH6139

www.vishay.com For technical questions, contact: optocoupleranswers@vishay.com
Document Number: 83669
4 Rev. 1.8, 19-Oct-10
SFH6138, SFH6139
Vishay Semiconductors
High Speed Optocoupler, 100 kBd,
Low Input Current, High Gain
Note
(1)
Common mode transient immunity in logic high level is the maximum tolerable (positive) dV
cm
/dt on the leading edge of the common mode
pulse, V
CM
, to assure that the output will remain in a logic high state (i.e.V
O
> 2 V) common mode transient immunity in logic low level is the
maximum tolerable (negative) dV
cm
/dt on the trailing edge of the common mode pulse signal, V
CM
, to assure that the output will remain in a
logic low state (i.e. V
O
< 0.8 V).
In applications where dv/dt may exceed 50 000 V/μs (such as state discharge a series resistor, R
CC
should be included to protect I
C
from
destructively high surge currents. The recommended value is R
CC
[IV/0.15 I
F
(mA)] kΩ
Note
As per IEC 60747-5-5, §7.4.3.8.1, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with
the safety ratings shall be ensured by means of protective circuits.
COMMON MODE TRANSIENT IMMUNITY
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Common mode transient immunity
at logic high level output
(1)
I
F
= 0 mA, R
L
= 2.2 kΩ,
R
CC
= 0, V
CM
= 10 V
P-P
CM
H
500 V/μs
Common mode transient immunity
at logic low level output
(1)
I
F
= 16 mA, R
L
= 2.2 kΩ,
R
CC
= 0, V
CM
= 10 V
P-P
CM
H
- 500 V/μs
SAFETY AND INSULATION RATINGS
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Climatic classification
(according to IEC 68 part 1)
55/100/21
Comparative tracking index CTI 175 399
V
IOTM
8000 V
V
IORM
890 V
P
SO
500 mW
I
SI
300 mA
T
SI
175 °C
Creepage distance Standard DIP-8 7 mm
Clearance distance Standard DIP-8 7 mm
Creepage distance 400 mil DIP-8 8 mm
Clearance distance 400 mil DIP-8 8 mm
Document Number: 83669 For technical questions, contact: optocoupleranswers@vishay.com
www.vishay.com
Rev. 1.8, 19-Oct-10 5
SFH6138, SFH6139
High Speed Optocoupler, 100 kBd,
Low Input Current, High Gain
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
PACKAGE MARKING
i178006
Pin one ID
6.645 ± 0.165
9.77 ± 0.14
0.95 ± 0.19
4° typ.
2.54 typ.
10°
3° to 9°
7.62 typ.
0.51 ± 0.05
0.25 ± 0.05
3.045 ± 0.255
3.555 ± 0.255
0.70 ± 0.19
6.095 ± 0.255
4
3
2
1
0.79
1.27
5
6
7 8
ISO method A
21764-67
SFH6138
V YWW H 68
Legal Disclaimer Notice
www.vishay.com
Vishay
Revision: 08-Feb-17
1
Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED

SFH6139

Mfr. #:
Manufacturer:
Description:
High Speed Optocouplers 100kbd Low Input Current High Gain
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet