Narrow pitch connectors A4US (0.4mm pitch)
–2–
ACCTB4E 201409-T
PRODUCT TYPES
Notes: 1. Order unit:
For volume production: 1-inner carton (1-reel) units
Samples for mounting check: 50-connector units. Please contact our sales office.
Samples: Small lot orders are possible. Please contact our sales office.
2. Please contact us for connectors having a number of pins other than those listed above.
SPECIFICATIONS
1. Characteristics
Mated height Number of pins
Part number Packing
Socket Header Inner carton (1-reel) Outer carton
0.8mm
10 AXE110527D AXE210124D
10,000 pieces 20,000 pieces
14 AXE114527D AXE214124D
18 AXE118527D AXE218124D
20 AXE120527D AXE220124D
24 AXE124527D AXE224124D
30 AXE130527D AXE230124D
34 AXE134527D AXE234124D
36 AXE136527D AXE236124D
40 AXE140527D AXE240124D
50 AXE150527D AXE250124D
60 AXE160527D AXE260124D
70 AXE170527D AXE270124D
80 AXE180527D AXE280124D
1.0mm
10 AXE110224D AXE210224D
20 AXE120224D AXE220224D
34 AXE134224D AXE234224D
40 AXE140224D AXE240224D
60 AXE160224D AXE260224D
80 AXE180224D AXE280224D
1.5mm
20 AXE120224D AXE220324D
60 AXE160224D AXE260324D
80 AXE180224D AXE280324D
Item Specifications Conditions
Electrical
characteristics
Rated current 0.30A/pin contact (Max. 5 A at total pin contacts)
Rated voltage 60V AC/DC
Breakdown voltage 150V AC for 1 min.
No short-circuiting or damage at a detection current of 1 mA
when the specified voltage is applied for one minute.
Insulation resistance Min. 1,000MΩ (initial) Using 250V DC megger (applied for 1 min.)
Contact resistance Max. 90mΩ
Based on the contact resistance measurement method
specified by JIS C 5402.
Mechanical
characteristics
Composite insertion force Max. 0.981N/pin contacts × pin contacts (initial)
Composite removal force Min. 0.165N/pin contacts × pin contacts
Contact holding force
(Socket contact)
Min. 0.20N/pin contacts
Measuring the maximum force.
As the contact is axially pull out.
Environmental
characteristics
Ambient temperature –55°C to +85°C No freezing at low temperatures. No dew condensation.
Soldering heat resistance
Peak temperature: 260°C or less (on the surface of
the PC board around the connector terminals)
Infrared reflow soldering
300°C within 5 sec. 350°C within 3 sec. Soldering iron
Storage temperature
–55°C to +85°C (product only)
–40°C to +50°C (emboss packing)
No freezing at low temperatures. No dew condensation.
Thermal shock resistance
(header and socket mated)
5 cycles,
insulation resistance min. 100MΩ,
contact resistance max. 90mΩ
Conformed to MIL-STD-202F, method 107G
Humidity resistance
(header and socket mated)
120 hours, insulation resistance min. 100MΩ,
contact resistance max. 90mΩ
Bath temperature 40±2°C,
humidity 90 to 95% R.H.
Saltwater spray resistance
(header and socket mated)
24 hours, insulation resistance min. 100MΩ,
contact resistance max. 90mΩ
Bath temperature 35±2°C,
saltwater concentration 5±1%
H2S resistance
(header and socket mated)
48 hours, contact resistance max. 90mΩ
Bath temperature 40±2°C, gas concentration 3±1 ppm,
humidity 75 to 80% R.H.
Lifetime
characteristics
Insertion and removal life 30 times
Repeated insertion and removal speed of max. 200 times/
hours
Unit weight
60 pin contacts Socket (h = 0.8mm: 0.03g, h = 1.0/1.5mm: 0.04g)
Header (h = 0.8mm: 0.02g, h = 1.0mm: 0.02g, h = 1.5mm: 0.03g)
Order Temperature (°C) Time (minutes)
1
2
3
4
–55
85
–55
0
−3
30
Max. 5
30
Max. 5
+3
0
0
−3