LB11961-TLM-E

LB11961
www.onsemi.com
7
*6. FG output
This is an open collector output, and a rotation count detection function can be implemented using this FG output, which
corresponds to the phase switching. This pin must be left open if unused.
*7. HB pin
This pin provides a Hall effect sensor bias constant-voltage output of 1.25V.
*8. RMI pin
Connect this pin to VTH if unused. Even if unused, the IC is set internally to operate at a 10% drive duty at the voltage
corresponding to the lowest speed. (The capacitor is used to set up full-speed mode at startup.)
Control Timing Chart
1. Set minimum speed mode
A VTH voltage level is generated when the thermistor detects the set temperature. At low temperatures, the fan
motor turns at the lowest speed, which is set with the RMI pin. The LB11961 compares the CPWM oscillator
voltage with the RMI pin voltage and sets the duty for the lowest drive state.
2. High speed low speed mode
The PWM signal is controlled by comparing the CPWM oscillation voltage that cycles between 1.2V and 3. 8V and
the VTH voltage.
When the VTH voltage is lower, the high and low side transistors are turned on, and when the VTH voltage is higher,
the high side transistor is turned off and the coil current is regenerated through the low side transistor. Thus the
output on duty increases as the VTH voltage becomes lower, the coil current increases, and the motor speed
increases.
Rotation speed feedback is provided by the FG output.
3. Full-speed mode
The LB11961 switches to full-speed mode above a certain temperature.
4. Thermistor removed mode
If the thermistor is removed, the VTH input voltage will rise. However, the output will go to full drive at 100% and
the motor will run at full speed.
THERMISTOR
REMOVED
V
CC
CPWM
3.6V
2.0V
PWM control variable speed mode
Full speed mode
0V
0V
12V
f = 25kHz (CP=100pF)
Low on duty
High on duty
FG
Set minimum
speed
RMI voltage
Internal lowest speed setting voltage
(V
CC
30%)
(V
CC
16%)
(V
CC
28%)
High
temperature
Low
tem
p
erature
LB11961
www.onsemi.com
8
ORDERING INFORMATION
Device Package Wire Bond Shipping(Qty/Packing)
LB11961-MPB-H HSSOP14(225mil)
(Pb-Free / Halogen Free)
Au-wire 70 / Fan-fold
LB11961-TLM-H HSSOP14(225mil)
(Pb-Free / Halogen Free)
Au-wire 2000 / Tape & Reel
LB11961-W-AH HSSOP14(225mil)
(Pb-Free / Halogen Free)
Cu-wire 2000 / Tape & Reel
† For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D. http://www.onsemi.com/pub_link/Collateral/BRD8011-D.PDF
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries
in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other
intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON
Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or
use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is
responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or
standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters,
including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its
patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support
systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for
implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall
indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an
Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

LB11961-TLM-E

Mfr. #:
Manufacturer:
ON Semiconductor
Description:
Motor / Motion / Ignition Controllers & Drivers 1PH DRV SENSOR OPEN ; SIN
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet