OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

2980526

P1-P3
© PHOENIX CONTACT - 03/2008
102490_en_01
INTERFACE
PLC-OSP-…/24DC/3RW
Data Sheet
1Description
Ultra-slim PLC interfaces with the user-friendly plug-in
bridge system now offer an extended range of optocoupler
interfaces for applications in electrical equipment in rail
vehicles.
The new PLC-OSP-…/24DC/3RW interface modules with
extended input voltage and temperature range are
designed for use according to DIN EN 50155
(VDE 0115-200) "Railway Applications Part 200: Electronic
Equipment Used on Rolling Stock".
The slim 6.2 mm PLC-OSP-...RW version has been
specially developed for applications on rail vehicles, which
are operated with an AC voltage, where the operating
voltage is supplied via contact lines using a transformer with
charger and battery.
The PLC-OSP-...RW is designed with a permissible
operating voltage of 0.7 ... 1.25 x U
N
.
The temperature of the air inside the vehicle and its housing
can increase to up to +70°C due to external influences. This
extreme requirement is easily met by the PLC-OSP-...RW
with its temperature range of -25°C to +70°C.
PLC-OSP-…/24DC/3RW offers shock resistance according
to EN 50155 (requirements according to EN 61373).
1.1 Additional PLC Advantages
– Integrated input/protective circuit
– User-friendly, vibration-resistant, and time-saving plug-
in bridge system
Make sure you always use the latest documentation.
It can be downloaded at www.download.phoenixcontact.com
.
A conversion table is available on the Internet at
www.download.phoenixcontact.com/general/7000_en_00.pdf.
This data sheet is valid for all products listed on the following page:
PLC INTERFACE With Extended Input Voltage and
Temperature Range for Railway Applications
PLC-OSP-…/24DC/3RW
102490_en_01 PHOENIX CONTACT 2
2Ordering Data
3 Technical Data
PLC INTERFACE
Description Type Order No. Pcs./Pck.
Single-channel optocoupler for railway applications, 24 V DC input voltage,
with spring-cage connection, for mounting on
3
PLC-OSP- 24DC/24DC/3RW 2980513 10
Single-channel optocoupler for railway applications, 110 V DC input voltage,
with spring-cage connection, for mounting on
3
PLC-OSP-110DC/24DC/3RW 2980526 10
For the protection of input and output, inductive loads must be dampened with an effective protective circuit.
Accessories
Description Type Order No. Pcs./Pck.
Insulating plate PLC-ATP BK 2966841 25
For additional accessories such as power terminal blocks and plug-in bridges, please refer to the INTERFACE catalog or www.phoenixcontact.com.
Input Data ...24DC... ...110DC...
Nominal input voltage U
N
1
1
The PLC-ATP BK insulating plate must be installed for voltages greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules
(see "Accessories"). FBST 8-PLC... or FBST 500... is then used for potential bridging.
24 V DC 110 V DC
Permissible range (with reference to U
N
) 0.7 ... 1.25 x U
N
(t < 1 s = 0.6 ... 1.40 x U
N
)
Typical input current at U
N
8.5 mA 3 mA
Switch-on threshold U
ON
≥ 0.6 x U
N
Switch-off threshold U
OFF
≤ 0.3 x U
N
Typical response time at U
N
40 μs 80 μs
Typical release time at U
N
200 μs 600 μs
Transmission frequency at U
N
300 Hz 100 Hz
Input circuit Protection against polarity reversal
Status indicator Yellow LED
The PLC-ATP BK insulating plate should be used in the following cases: always fit at the start and end of a PLC terminal strip for voltages
greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules (FBST 8-PLC... or FBST 500... can be used for
potential bridging) and for safe isolation between adjacent modules.
Output Data ...24DC... ...110DC...
Nominal output voltage U
N
24 V DC
Permissible range (with reference to U
N
) 3 V DC ... 33 V DC (t < 1 s = 1.40 x U
N
)
Limiting continuous current 3 A (see "Derating Curve" on page 3)
Voltage drop at maximum limiting continuous current < 200 mV
Output configuration 2-wire floating
Output circuit Protection against polarity reversal, surge protection
Surge voltage limitation > 33 V DC
PLC-OSP-…/24DC/3RW
102490_en_01 3
PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany • Phone: +49 - 52 35 - 30 0
PHOENIX CONTACT • P.O.Box 4100 • Harrisburg • PA 17111-0100 • USA • Phone: +717-944-1300
www.phoenixcontact.com
4 Block Diagram 5 Derating Curve
Figure shows load current depending on the ambient
temperature for PLC-OSP-…/24DC/3RW. Operating time:
100% operating factor.
General Data
Rated insulation voltage 250 V
Impulse voltage withstand level 4 kV
Ambient temperature range
Operation
Storage/transport
-25°C ... 70°C
-40°C ... 85°C
Test voltage input/output 2.5 kV
rms
, 50 Hz, 1 min.
Nominal operating mode 100% operating factor
Air and creepage distances between the circuits
1
DIN EN 50178/VDE 0160 (basic insulation)
Standards/specifications DIN EN 50155/VDE 0115-200 (in relevant parts)
Pollution degree 2
Surge voltage category III
Mounting position Any
Mounting Can be aligned without spacing
Weight 40 g, approximately
Connection method Spring-cage connection
Conductor cross-section
Solid
Stranded
0.2 mm
2
... 2.5 mm
2
(24 - 14 AWG)
0.2 mm
2
... 2.5 mm
2
(24 - 14 AWG)
Stripping length 8 mm
Dimensions (W x H x D) 6.2 mm x 86 mm x 80 mm
Housing material Polybutylene terephthalate PBT, non-reinforced, green
1
The PLC-ATP insulating plate must be installed for safe isolation between adjacent modules (see "Accessories"). FBST 8-PLC... or FBST 500... is then
used for potential bridging.
Approvals
CE
c
UL/CUL Applied for
A1
A2
A2
14
14
13+
13+
Ambient temperature [°C]
Load current [A]
In rows with zero spacing
in rows with > 20 mm spacing
1
20 30 40 50 60 70
1,5
2
2,5
3
1
2
1
2
P1-P3

2980526

Mfr. #:
Buy 2980526
Manufacturer:
Phoenix Contact
Description:
Solid State Relays - Industrial Mount PLC-OSP-110DC/ 24DC/3RW
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet