OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

EAPL3527RA3

P1-P3P4-P6P7-P9
DATASHEET
SMD TOP View LEDs
EAPL3527RA3
7
Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 28.04.2014. Issue No: 1
www.everlightamericas .com
Moisture Resistant Packing Materials
Label Explanation
‧CPN: Customer’s Product Number
‧P/N: Product Number
‧QTY: Packing Quantity
‧CAT: Luminous Intensity Rank
‧HUE: Dom. Wavelength Rank
‧REF: Forward Voltage Rank
‧LOT No: Lot Number
Reel Dimensions
Carrier Tape Dimensions: Loaded Quantity 2000 pcs Per Reel
Note: Tolerances unless mentioned ±0.1mm. Unit = mm
DATASHEET
SMD TOP View LEDs
EAPL3527RA3
8
Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 28.04.2014. Issue No: 1
www.everlightamericas .com
Moisture Resistant Packing Process
Note: Tolerances unless mentioned ±0.1mm. Unit = mm
Precautions for Use
1. Over-current-proof
1.1 Customer must apply resistors for protection, otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
Pre-heating
150~200¢XC
60~120sec.
3¢XC/sec.Max.
Above 217¢XC
60~150sec.
260¢XC Max.
10sec. Max.
6¢XC/sec.Max.
Above255¢XC
30sec.Max.
2. Storage
2.1 Moisture proof bag should only be opened immediately prior to usage.
2.2 Environment should be less than 30℃ and 60% RH when moisture proof bag is opened.
2.3 After opening the package MSL Conditions stated on page 1 of this spec should not be exceeded.
2.4 If the moisture sensitivity card indicates higher than acceptable moisture, the component should be baked at
min. 60deg +/-5deg for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less
than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be
DATASHEET
SMD TOP View LEDs
EAPL3527RA3
9
Copyright © 2010, Everlight Americas Inc. All Rights Reserved. Release Date : 28.04.2014. Issue No: 1
www.everlightamericas .com
careful because the damage of the product is often started at the time of the hand solder.
5. Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head
soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of
the LEDs will or will not be damaged by repairing.
Application Restrictions
High reliability applications such as military/aerospace, automotive safety/security systems,
and medical equipment may require different product. If you have any concerns, please contact
Everlight before using this product in your application. This specification guarantees the quality
and performance of the product as an individual component. Do not use this product beyond the
specification described in this document.
Revision History
Rev.
Modified date
File modified contents
1
2014/4/28
New Spec
P1-P3P4-P6P7-P9

EAPL3527RA3

Mfr. #:
Buy EAPL3527RA3
Manufacturer:
Description:
Standard LEDs - SMD Top-View PLCC
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet