NOTES: (UNLESS OTHERWISE SPECIFIED)
1. ALL DIMENSIONS ARE IN INCHES [mm].
2. DIMENSIONS APPLY AFTER FINISHING.
3. MANUFACTURE TO BE COMPLIANT WITH EU RoHS DIRECTIVE.
4. SAFETY BREAK ALL SHARP CORNERS AND EDGES .02 MAXIMUM.
SHEET 1 OF 1
LDCFDLT_A
SCALE: 2:1
TITLE:
SIZE
DWG. NO.
REV
DO NOT SCALE DRAWING
ANGLES:
1
TOLERANCES:
.020 [0.50]-.200 [5.00]=
.008 [0.20]
.200 [5.00]-1.200 [30.00]=
.016 [0.40]
1.20 [30.0]-4.75 [120.0]=
.024 [0.60]
4.75 [120.0]-12.40 [315.0]=
.040 [1.0]
DRAWN:
ENGR:
DT:
DT:
MATERIAL:
FINISH:
PROJECTION:
:
THIS DRAWING CONTAINS PROPRIETARY INFORMATION
THAT IS THE SOLE PROPERTY OF LINX TECHNOLOGIES, AND SHALL BE
TREATED AS SUCH. NO DISCLOSURE OR REPRODUCTION OF THIS
DOCUMENT IS PERMITTED, IN WHOLE OR IN PART, WITHOUT THE
EXPRESS WRITTEN PERMISSION OF LINX TECHNOLOGIES OR ITS
DESIGNATED AGENTS.
159 ORT LANE
MERLIN, OR 97532
REVISIONS
REV
DESCRIPTION
DATE
APPV
A CJ
B
10-JUL-12
B.MURPHY
S.HOGAN
10-JUL-12
Add heat shrink, new frame,revised stripping instruct./dims 4/21/10
RECOMMENDED CABLE STRIPPING DIMENSIONS
SIDE VIEW
0.354
(9.00)
Ø0.049
(1.24)
Ø0.024
(0.60)
PIN CHUCK
0.2x2x2mm GROOVE
Ø0.020
(0.50)
SOCKET
RECOMMENDED
MOUNTING HOLE
0.234
[6.00]
Ø0.256
[6.50]
HEAT SHRINK
0.020
[0.50]
0.065
[1.65]
NUT
1/4-36UNS-2B
THREADS
H0.315
[8.00]
Ø0.402
[10.20]
WASHER
0.055
(1.40)
Ø0.236
(6.00)
Ø0.358
(9.10)
O-RING
CONSMA014-R178
Descripon Material Finish
Body
Socket
Insulaon
Nickel
N/A
Gold
PTFE
Spacer N/APTFE
O Ring RubberSI Rubber
Washer NickelBrass
Nut NickelBrass
Support NickelBrass
Heat Shrink BlackPolyolefin
Brass
BE CU
0.197
(5.00)
0.032
(0.80)
0.217
(5.50)
RG-178 Cable
CONSMA014-R178 ASSEMBLY INSTRUCTIONS
1. Strip the cable to the recommended dimensions.
2. Slide the coax into the support until the outside insulation bottoms out
against the inside shoulder of the support.
3. Solder the support onto the braid.
4. Place the spacer onto the center conductor.
5. Solder or crimp the socket onto the center conductor.
6. Insert the socket, center conductor, spacer, and support into the body
until the top of the socket is even with the white insulation in the body.
7. Crimp the tail of the body onto the support with a 0.093” hex crimp tool.
0.787
(20.00)
Ø0.118
(3.00)
0.197
(5.00)
0.248
(6.30)
0.083
(2.10)
0.417
(10.60)
0.748
(19.00)
FLAT 0.228
(5.80)
Ø0.102
(2.60)
Ø0.236
(6.00)
H0.433
(11.00)
1/4"-36UNS-2A
THREADS
SUPPORTSPACER
SMA FEMALE BULKHEAD MOUNT CABLE
END CRIMP WITH O-RING FOR RG178 CABLE
B BPMUpdated footprint and dimensions; Added new title block 10-JUL-12
