OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

HFBR-2532Z

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18
7
HFBR-15X1Z Transmitter
All HFBR-15XXZ LED transmitters are classied as IEC 825-1 Accessible Emission Limit (AEL) Class 1 based upon the current proposed
draft scheduled to go into eect on January 1, 1997. AEL Class 1 LED devices are considered eye safe. Contact your local Avago sales
representative for more information.
Absolute Maximum Ratings
Parameter Symbol Min. Max. Units Reference
Storage Temperature T
S
–40 +85 °C
Operating Temperature T
A
–40 +85 °C
Lead Soldering Cycle Temp. 260 °C Note 1, 4
Time 10 sec
Forward Input Current I
FPK
1000 mA Note 2, 3
I
Fdc
80
Reverse Input Voltage V
BR
5 V
Notes:
1. 1.6 mm below seating plane.
2. Recommended operating range between 10 and 750 mA.
3. 1 µs pulse, 20 µs period.
4. Moisture sensitivity level (MSL) is 3.
ANODE
1
CATHODE
2
N.C.
3
N.C.
4
8 DO NOT CONNECT
5 DO NOT CONNECT
Pin # Function
1 Anode
2 Cathode
3 Open
4 Open
5 Do not connect
8 Do not connect
Note: Pins 5 and 8 are for mounting and retaining purposes only. Do not
electrically connect these pins.
8
Figure 9. Typical forward voltage vs. drive current Figure 10. Normalized typical output power vs. drive current
V
F
– FORWARD VOLTAGE – V
2
1.8
1.6
1.4
I
Fdc
– TRANSMITTER DRIVE CURRENT (mA)
10
1.7
1.5
100
70°C
25°C
0°C
P
T
– NORMALIZED OUTPUT POWER – dB
2
5
-5
-20
I
Fdc
– TRANSMITTER DRIVE CURRENT (mA)
10
0
-15
100
-10
Transmitter Electrical/Optical Characteristics 0 °C to 70 °C, unless otherwise specied.
Parameter Symbol Min. Typ.
[5]
Max. Units Conditions Ref.
Transmitter Output P
T
-16.5 -7.6 dBm I
Fdc
= 60 mA Notes 1, 2
-14.3 -8.0 dBm I
Fdc
= 60 mA, 25 °C
Output Optical Power ∆P
T
/∆T -0.85 %/°C
Temperature Coecient
Peak Emission λ
PK
660 nm
Wavelength
Forward Voltage V
F
1.45 1.67 2.02 V I
Fdc
= 60 mA
Forward Voltage ∆V
F
/∆T -1.37 mV/°C Fig. 9
Temperature Coecient
Eective Diameter D 1 mm
Numerical Aperture NA 0.5
Reverse Input Breakdown V
BR
5.0 11.0 V I
Fdc
= 10 µA,
Voltage T
A
= 25°C
Diode Capacitance C
O
86 pF V
F
= 0, f = MHz
Rise Time t
r
80 ns 10% to 90%, Note 3
Fall Time t
f
40 ns
Notes:
1. Measured at the end of 0.5 m standard ber optic cable with large area detector.
2. Optical power, P (dBm) = 10 Log [P(µW)/1000 µW].
3. Rise and fall times are measured with a voltage pulse driving the transmitter and a series connected 50 Ω load. A wide bandwidth optical to
electrical waveform analyzer, terminated to a 50 Ω input of a wide bandwidth oscilloscope, is used for this response time measurement.
Optical Power
I
F
= 60 mA
9
HFBR-25X1Z Receiver
Absolute Maximum Ratings
Parameter Symbol Min. Max. Units Reference
Storage Temperature T
S
–40 +85 °C
Operating Temperature T
A
–40 +85 °C
Lead Soldering Cycle Temp. 260 °C Notes 1, 3
Time 10 sec
Supply Voltage V
CC
–0.5 7 V Note 2
Output Collector Current I
OAV
25 mA
Output Collector Power Dissipation P
OD
40 mW
Output Voltage V
O
–0.5 18 V
Pull-up Voltage V
P
–5 V
CC
V
Fan Out (TTL) N 5
Receiver Electrical/Optical Characteristics 0 °C to 70 °C, 4.75 V ≤ V
CC
≤5.25 V, unless otherwise specied.
Parameter Symbol Min. Typ. Max. Units Conditions Ref.
Input Optical Power P
R(L)
–21.6 –9.5 dBm V
OL
= 0.5 V Notes 1,
Level for Logic “0” I
OL
= 8 mA 2, 4, 5
–21.6 –8.7 V
OL
= 0.5 V
I
OL
= 8 mA, 25 °C
Input Optical Power P
R(H)
–43 dBm V
OL
= 5.25 V Notes 1, 5
Level for Logic “1” I
OH
≤ 250 µA
High Level Output Current I
OH
5 250 µA V
O
= 18 V, P
R
= 0 Notes 3, 5
Low Level Output Current V
OL
0.4 0.5 V I
OL
= 8 mA, Notes 3, 5
P
R
= P
R(L)MIN
High Level Supply I
CCH
3.5 6.3 mA V
CC
= 5.25 V, Notes 3, 5
Current P
R
= 0
Low Level Supply Current I
CCL
6.2 10 mA V
CC
= 5.25 V Notes 3, 5
P
R
= -12.5 dBm
Eective Diameter D 1 mm
Numerical Aperture NA 0.5
Internal Pull-up Resistor R
L
680 1000 1700 Ω
Pin # Function
1 V
O
2 Ground
3 V
CC
4 R
L
5 Do not connect
8 Do not connect
Note: Pins 5 and 8 are for mounting and retaining purposes only. Do not
electrically connect these pins.
4
3
2
1
DO NOT CONNECT 5
DO NOT CONNECT 8
R
L
V
CC
GROUND
V
O
1000 Ω
Notes:
1. 1.6 mm below seating plane.
2. It is essential that a bypass capacitor 0.1 µF be connected from pin 2 to pin 3 of the receiver. Total lead length between both ends of the capacitor
and the pins should not exceed 20 mm.
3. Moisture sensitivity level (MSL) is 3.
Notes:
1. Optical ux, P (dBm) = 10 Log [P (µW)/1000 µW].
2. Measured at the end of the ber optic cable with large area detector.
3. R
L
is open.
4. Pulsed LED operation at I
F
> 80 mA will cause increased link t
PLH
propagation delay time. This extended t
PLH
time contributes to increased pulse
width distortion of the receiver output signal.
5. Guaranteed only if optical input signal to the receiver is generated by HFBR-15x1Z, with ideal alignment to photo diode using 1 mm POF (NA=0.5).
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18

HFBR-2532Z

Mfr. #:
Buy HFBR-2532Z
Manufacturer:
Broadcom / Avago
Description:
Fiber Optic Transmitters, Receivers, Transceivers V-LINK VERTICAL 1MBd RCVR RoHS
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet