HMC553ALC3B Data Sheet
Rev. A | Page 22 of 25
SPURIOUS AND HARMONICS PERFORMANCE
LO Harmonics
LO = 13 dBm, all values in dBc below input LO level and
measured at RF port. N/A means not applicable.
Table 5. LO Harmonics at RF
N × LO Spur at RF Port (dBc)
LO Frequency (GHz) 1 2 3 4
6 37 21 51 53
8 38 41 43 64
9 38 46 49 70
10 37 45 58 82
12 37 50 45 82
14 39 50 71 N/A
LO = 13 dBm, all values in dBc below input LO level and
measured at IF port. N/A means not applicable.
Table 6. LO Harmonics at IF
N × LO Spur at IF Port (dBc)
LO Frequency (GHz) 1 2 3 4
6 43 38 60 74
8 28 50 88 104
9 29 66 102 109
10 29 76 103 108
12 31 84 88 10
14 43 93 107 N/A
M × N Spurious Outputs
Downconversion, Upper Sideband
Spur values are (M × RF) − (N × LO). RF = 10.1 GHz, LO =
10 GHz, RF power = −10 dBm, and LO power = 13 dBm. Mixer
spurious products are measured in dBc from the IF output power
level. N/A means not applicable.
N × LO
0 1 2 3 4
M × RF
0
0 0.6 26 25 729
1
22 0 44 70 68
2
71 67 58 70 78
3
84 92 93 71 91
4
0 82 93 98 101
Downconversion, Lower Sideband
Spur values are (M × RF) − (N × LO). RF = 14 GHz, LO =
14.1 GHz, RF power = −10 dBm, and LO power = 13 dBm.
Mixer spurious products are measured in dBc from the IF
output power level. N/A means not applicable.
N × LO
0 1 2 3 4
M × RF
0
0 3 26 0 0
1
18 0 40 65 0
2
55 72 70 77 56
3
0 57 93 74 89
4
0 0 58 95 101
Upconversion, Upper Sideband
Spur values are (M × IF
IN
) + (N × LO). IF
IN
= 0.1 GHz, LO =
10 GHz, RF power = −10 dBm, and LO power = 13 dBm. Mixer
spurious products are measured in dBc from the RF output power
level. N/A means not applicable.
N × LO
0 1 2 3 4
M × IF
IN
−5
102 99 96 64 61
−4
103 86 94 62 61
−3
97 81 83 75 61
−2
81 51 59 72 59
−1
36 0 35 22 43
0
N/A 6 10 27 19
+1
36 0 36 20 45
+2
81 50 58 68 56
+3
95 63 84 76 66
+4
101 85 92 84 62
+5
102 100 94 84 65
Upconversion, Lower Sideband
Spur values are (M × IF
IN
) + (N × LO).
IF
IN
= 0.1 GHz, LO = 14.1 GHz, RF power = −10 dBm, and
LO power = 13 dBm. Mixer spurious products are measured in
dBc from the RF output power level. N/A means not applicable.
N × LO
0 1 2 3 4
M × IF
IN
−5
100 96 82 N/A N/A
−4
98 85 84 N/A N/A
−3
95 71 77 N/A N/A
−2
78 52 60 N/A N/A
−1
35 0 28 N/A N/A
0
N/A 8 20 N/A N/A
+1
34 0 28 N/A N/A
+2
79 50 61 N/A N/A
+3
96 63 61 N/A N/A
+4
100 86 84 N/A N/A
+5
100 95 62 N/A N/A
Data Sheet HMC553ALC3B
Rev. A | Page 23 of 25
THEORY OF OPERATION
The HMC553ALC3B is a general-purpose, double-balanced
mixer that can be used as an upconverter or a downconverter
from 6 GHz to 14 GHz.
When used a downconverter, the HMC553ALC3B downconverts
radio frequencies (RF) between 6 GHz and 14 GHz to intermediate
frequencies (IF) between dc and 5 GHz.
When used as an upconverter, the mixer upconverts intermediate
frequencies between dc and 5 GHz to radio frequencies between
6 GHz and 14 GHz.
HMC553ALC3B Data Sheet
Rev. A | Page 24 of 25
APPLICATIONS INFORMATION
TYPICAL APPLICATION CIRCUIT
Figure 82 shows the typical application circuit for the
HMC553ALC3B. The HMC553ALC3B is a passive device and
does not require any external components. The LO and RF pins
are internally ac-coupled. The IF pin is internally dc-coupled.
When IF operation to dc is not required, use of an external
series capacitor is recommended, of a value chosen to pass the
necessary IF frequency range. When IF operation to dc is
required, do not exceed the IF source and sink current rating
specified in the Absolute Maximum Ratings section.
GND
GND
RF
GND
NI
C
NI
C
NI
C
GND
LO
LO RF
IF
GND
IF
GND
HMC553ALC3B
16420-084
1
7
8
9
101112
4
2
3
56
Figure 82. Typical Application Circuit
EVALUATION PCB INFORMATION
Use RF circuit design techniques for the circuit board used in
the application. Ensure that signal lines have 50 Ω impedance,
and connect the package ground leads and the exposed pad
directly to the ground plane (see Figure 83). Use a sufficient
number of via holes to connect the top and bottom ground
planes. The evaluation circuit board shown in Figure 83 is
available from Analog Devices, Inc., upon request.
Table 7. List of Materials for Evaluation PCB
EV1HMC553ALC3B
Item Description
J1, J2 SRI 2.92 mm connector
J3 Johnson Surface-Mount Type A (SMA) connector
U1 HMC553ALC3B
PCB
1
117611-7 evaluation board
1
117611-7 is the raw bare PCB identifier. Reference EV1HMC553ALC3B when
ordering the complete evaluation PCB.
J1
J3
IF
LO RF
117611–7
U1
J2
16420-085
553A
Figure 83. Evaluation PCB Top Layer

HMC553ALC3B

Mfr. #:
Manufacturer:
Analog Devices Inc.
Description:
RF Mixer WidebandPassiveMixer
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet