HBS150ZG-ANT Datasheet HBS150ZG-ANT, HBS150YH-A | P1-P3

TECHNICAL SPECIFICATIONS

HBS SERIES - 150 WATT

REV. 12/01

HBS single output DC/DC converters provide up to 150

Watts of output power in an industry standard, half-brick

package and footprint. The HBS series features excellent

efficiency, Class A conducted noise specifications, and

fixed switching frequency. The HBS features open-frame

packaging, along with planar magnetics to provide maxi-

mum useable power with minimal thermal constraints.

The HBS series is well suited for telecom, networking, and

industrial applications, and is fully compatible with

production board washing processes

DESCRIPTION

FEATURES

Notes

†

MTBF predictions may vary slightly from model to model.

Specifications typically at 25°C, normal line, and full load,

unless otherwise stated.

Soldering Conditions: I/O pins, 260°C, ten seconds; fully

compatible with commercial wave-soldering equipment.

Units are water-washable and fully compatible with commercial

spray or immersion post wave-solder washing equipment.

Turn-On Time 10 ms

Remote Shutdown Positive or Negative Logic

Remote Shutdown Reference V

Negative

Switching Frequency 500 kHz

Isolation

Input - Output 1500 VDC

Input - Case 1050 VDC

Output - Case 500 VDC

Temperature Coefficient 0.2%/°C

Case Temperature

Operating Range -40 to +100°C

Storage Range -40 to +125°C

Thermal Shutdown Range 105 to 115°C

Vibration, 3 Axes, 5 Min Each 5 g, 10 - 55 Hz

MTBF

†

(Bellcore TR-NWT-000332) 2.1 x 10

hrs

Safety UL, cUL, VDE

Weight (approx.) 2.5 oz

General

• Industry Standard Half-

Brick

• Open-Frame Packaging

• 100°C Baseplate Operation

• Water Washable

• “True-Trim” Option

• 1500V Isolation

• Positive Or Negative

Logic

Setpoint Accuracy ±1%

Line Regulation V

Min. - V

Max., I

out

Rated ±0.2% V

out

Load Regulation I

out

Min. - I

out

Max., V

Nom. ±0.2% V

out

Remote Sense Headroom 0.5 VDC

Minimum Output Current 10%, I

out

Rated

Dynamic Regulation, Loadstep 25% I

out

Pk Deviation 4% V

out

Settling Time 500 ms

Voltage Trim Range ±10%

Short Circuit / Overcurrent Protection Hiccup

Current Limit Threshold Range, % of I

out

Rated 110 - 140%

OVP Trip Range 115 - 140% V

out

Nom.

OVP Hiccup

Output

Voltage range

24 VDC nominal 18 - 36 VDC

48 VDC nominal 34 - 75 VDC

Reflected ripple 25 mA

Input Reverse Voltage Protection Shunt Diode

Input

HBS150ZG-A

10 20 30 40 50 60 70 80 90 100

LOAD %

EFFICIENCY %

EFF. (34V)

EFF. (48V)

EFF. (75V)

Efficiency vs. Load (48V Input)

MECHANICAL DRAWING

HBS SERIES - 150 WATT

MODEL

INPUT VOLTAGE INPUT VOLTAGE MAXIMUM INPUT OUTPUT RATED OUTPUT RIPPLE & NOISE TYPICAL

(VOLTS) RANGE (VOLTS) CURRENT (AMPS)* VOLTAGE (VOLTS) CURRENT (AMPS) pk-pk (mV) EFFICIENCY**

HBS150YG-A 24 18-36 11.7 5 30 100 80%

HBS150YH-A 24 18-36 10.5 12 12.5 150 85%

HBS150ZG-A 48 34-75 5.84 5 30 100 83%

HBS150ZH-A 48 34-75 5.2 12 12.5 150 86%

HBS150ZJ-ANT 48 34-75 5.2 15 10 150 84%

NOTES:

* Maximum input current at minimum input voltage, maximum rated output power.

** At nominal V

, rated output.

MODELS - (See the last page of section for options.)

Thermal Impedance

Natural Convection 3.4 °C/W

100 LFM 2.7 °C/W

200 LFM 2.2 °C/W

300 LFM 1.8 °C/W

400 LFM 1.6 °C/W

Tolerances

Note:

Thermal impedance data is

dependent on many environmental

factors. The exact thermal

performance should be validated

for specific application.

1-V

2 Case

3 On/Off

4+V

5-V

out

6 -Sense

7 Trim

8 +Sense

9+V

out

Inches: (Millimeters)

.XX ± 0.020 .X ± 0.5

.XXX ± 0.010 .XX ± 0.25

Pin:

± 0.002 ± 0.05

(Dimensions as listed unless

otherwise specified.)

Pin Function

OPTION SUFFIX APPLICABLE SERIES REMARKS

Negative Logic N HAS, HBD, HBS, HES, HLS, HLD, LES, TTL "Low" Turns Module ON

QBS, QES, QLS, TES, TQD TTL "High" Turns Module OFF

Lucent-Compatible T HAS, HBD, HBS, HES, HLS, QBS, QES,

QLS

Terminal Strip TS XWS, XWD, XWT

Trim 1 IAS, LES

Enable 2 IAD, IAS, LES, SMS

Trim and Enable 3 IAS, LES

Current Share 4 SMS

Headerless Y Encapsulated EWS, IWS, OWS

Pin Length and Heatsink Options Standard Pin Length is 0.180" (4.6mm)

0.110" (2.8mm) Pin Length 8 All Units (Except SMS)

0.150" (3.8mm) Pin Length 9 All Units (Except SMS)

0.24" (6.1mm) Horizontal Heatsink 1H All Units (All Units Except DIP, HLS, HLD, QLS, Includes Thermal Pad