MINIMUM INSERTION LOSS IN dB
COMMON MODE (L-G) IN 50 OHM SYSTEM
DIFFERENTIAL MODE (L-L) IN 50 OHM SYSTEM
FREQUENCY-MHz
PART NO.
.15 .50 1.0 5.0 10 30
03KENG3EA/03KENW3EA 15 20 25 40 40 45
08KENG3EA/08KENW3EA 10 15 20 35 40 50
10KENG3EA/10KENW3EA 7 12 18 30 30 50
03KENG3SA/03KENW3SA 15 20 25 40 40 40
06KENG3SA/06KENW3SA 7 15 20 35 40 40
10KENG3SA/10KENW3SA 4 12 18 30 30 45
03KENG3EA/03KENW3EA 5 12 15 40 50 45
08KENG3EA/08KENW3EA 5 10 15 45 40 50
10KENG3EA/10KENW3EA 4 12 18 30 30 50
03KENG3SA/03KENW3SA
10 20 35 40 45 40
06KENG3SA/06KENW3SA
10 25 40 35 40 40
10KENG3SA/10KENW3SA
10 25 35 30 30 45
SERIES
SPECIFICATIONS
1. Maximum leakage current each
line-to-ground @ 115VAC 60Hz: 0.20mA
@ 250VAC 50Hz: 0.40mA
2. Hipot rating (one minute)
line-to-ground: 2250VDC
line-to-line: 1450VDC
3. Operating frequency: 50/60Hz
4. Rated voltage: 115/250VAC
HIGH PERFORMANCE SNAP-IN
FILTERS
2-12
MECHANICAL CONSTRUCTION
G3EA
W3EA
ELECTRICAL SCHEMATIC
Cx
Lg
G
L
N
E
N
I
L
L
G'
Cy
Cy
N'
L'
D
A
O
L
R
R: 1M /-R ONLY
IEC INLET FILTERS
COMPONENTS
**
**
*
*
VDE approved to 6A 250V.
UL, CSA & VDE approved to 9A 115/250 VAC.
PART NO. L (mH) Cx (uF) Cy (pF) Lg (uH)
03KENG3EA/03KENW3EA 3.1
08KENG3EA/08KENW3EA 0.8
10KENG3EA/10KENW3EA 0.4 0.1 2200 100
03KENG3SA/03KENW3SA 3.1
06KENG3SA/06KENW3SA 0.8
10KENG3SA/10KENW3SA 0.4
1. Specially designed with ground choke providing most effective
EMI suppression for high frequency noise (ranged 5MHz-25MHz).
2. Bleeder resistor can be added with suffix "-R" on part numbers.
3. With optional Y capacitor from 100pF to 3300pF.
4. All part numbers are UL recognized, CSA certified and VDE approved.
5.Optional side snap-in mounting clip type with suffix (H) on part numbers.
for 03/06/10KENG3SA series.
INTRODUCTIONS
G3SA
G
L
N
21.90 0.1
R0.08MAX.
R2.0MAX.
0.8~1.6
0.0315~0.063
SUGGESTED MOUNTING CUTOUT
+0.012
+0.3
28.45-0
1.12-0
0.862 0.004
24.0 0.5
0.945 0.02
31.5 0.5
1.22 0.02
+1.0
+0.04
-
0.14 0.02
-
3.6 0.5
1.12MAX.
28.4MAX.
42.16MAX.
1.66MAX.
2.1MAX.
53.4MAX.
21.4MAX.
0.84MAX.
UNIT:
INCH
mm
G3EA
G
L
N
21.3MAX.
21.90 0.1
R0.08MAX.
R2.0MAX.
0.8~1.6
0.0315~0.063
SUGGESTED MOUNTING CUTOUT
+0.012
+0.3
28.45-0
1.12-0
0.862 0.004
24.0 0.5
0.945 0.02
31.5 0.5
1.22 0.02
+1.0
+0.04
-
0.14 0.02
-
3.6 0.5
48.0MAX.
1.89MAX.
2.32 MAX.
59.0 MAX.
1.12MAX.
28.4MAX.
OROR
D
V
ED
V
E
W3EA
48.0MAX.
21.3 MAX.
0.84 MAX.
1.97 0.04
50.0 1.0
31.5 0.5
G
1.22 0.02
L
N
24.0 0.5
0.945 0.02
21.90 0.1
R0.08MAX.
R2.0MAX.
0.8~1.6
0.0315~0.063
SUGGESTED MOUNTING CUTOUT
+0.012
+0.3
28.45-0
1.12-0
0.862 0.004
Suggested thickness of mounting panel is from
0.0315 (0.8) to 0.063 (1.6) inch(mm) of mounting cutout
+1.0
+0.04
1.12MAX.
28.4MAX.
1.89MAX.
-
0.14 0.02
-
3.6 0.5
4.0MIN.
100.0MIN.
WIRE LENGTH : 4.0" MIN.
