OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

CY3653

P1-P3P4-P5
WirelessUSB™ PRoC™ Development Kit Tutorial
1. Introduction
This tutorial provides the developer with a basic, hands-on understanding of the
WirelessUSB™ PRoC™ technology using the CY3653 WirelessUSB PRoC Development kit.
It presents detailed pictures and step-by-step instructions to use the following tutorial
examples: Radio Tutorial, Protocol Slave Tutorial, and Protocol Master Tutorial.
2. Emulation and Programming
Before stepping through the process of emulation or programming, make sure that PSoC
Designer™ is installed, the MiniProg or ICE-Cube is connected to the PC with the provided
USB cable, and that all of the hardware assembly (from the WirelessUSB PRoC™ DVK Quick
Start Guide) has been done. When emulating, remove the PRoC Module from the PSoC
Eval1 board and replace it with the PRoC Development Module.
Note: Programming can be done by using either the MiniProg or the ICE-Cube. However, the
ICE-Cube is required for emulation. The ICE-Cube is available in the PSoC™ development kit
and can be ordered from Cypress’s online store (PSoC Development Kit, CY3215-DK)
Programming
Steps:
1. Launch PSoC Programmer software
4
3
9
5
8
7
6
2. Remove the power from the Eval1 board
3. Connect the MiniProg to the 5-pin ISSP header on the PSoC Eval1 board
4. In PSoC Programmer, click the “File Load” button to load the desired binary (hex) file
5. Select the MiniProg port
6. Select the “Power Cycle” Programming Mode
7. Select the 69xx “Device Family”
8. Select the CYWUSB6953-48LFXC “Device”
9. Click “Program” (It will go through programming and verification modes)
10. Once the programming is finished, remove the MiniProg from the Eval1 board
11. Connect the power to the Eval1 board
Cypress Semiconductor Corporation • 3901 North First Street • San Jose • CA 95134 • 408-943-2600
Emulation
3
9
6
4
5
7
8
2
Steps:
1. Launch the desired .SOC project file project from \Firmware\<application name>\
2. Replace the PRoC Module with the PRoC Development Module
3. Connect the Flex Pod to the ICE-Cube and PRoC Development Module
4. Select Config | Generate Application or select the above icon
5. Select Build | Build, hit F7, or select the above icon
6. Select Build | Start Debug, hit CTL+F5, or select the above icon
7. Select Debug | Connect, or select the above icon
8. Select Debug | Download to Emulator, or select the above icon
9. Select Debug | Go, hit F5, or select the above icon
WirelessUSB PRoC™ Development Kit Tutorial Page 2 of 5
3. Radio Tutorial
The Radio Tutorial shows the simplicity of transmitting data and receiving data using the
WirelessUSB LS user module. When the button (S1) is pushed, byte 0x55 is transmitted. If
the button is not being pressed, then it listens for byte (0x55). If the byte is received, either
LED1 or LED4 will light up. Follow the steps below:
Steps:
1. Program the first PRoC Module on one of the Eval1 boards by using Radio_Tutorial.hex
file located at \Firmware\Binaries\Radio_Tutorial.hex by following the “Programming”
instructions on
page 1.
2. Program the second board with the same hex file.
3. Push the button (S1) on either board.
3
Results:
An LED on the other board will light up. Every time the button is pushed, the other board
will switch between LED1 and LED4, if it is wired the same as in the assembly instructions
from the WirelessUSB PRoC DVK Quick Start Guide.
First Byte Received
Second Byte Received
WirelessUSB PRoC™ Development Kit Tutorial Page 3 of 5
P1-P3P4-P5

CY3653

Mfr. #:
Buy CY3653
Manufacturer:
Cypress Semiconductor
Description:
KIT DEVELOPMENT FOR PROC
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet