DO NOT
SCALE FROM
THIS PRINT
.405 10.29
REF
.380 9.65
REF
.130 3.30
.045
SQ REF
1.14
(TYP)
2
MAX SWAY
.165 4.19
(TYP)
(No OF POSITIONS - 1) x .165[4.19] ±.008[0.20]
"A"
"A"
T-1S55-01-X-2
IPBT-08-D
FIG 1
(IPBT-108-H1-XX-D SHOWN)
SEE NOTE 8
(No OF POSITIONS x .165[4.19]) + .053[1.33] REF
.378
REF
9.60
.205
REF
5.21
.050
REF
1.27
.165 4.19
(No OF POSITIONS - 1) x .165[4.19]
.109
REF
2.76
C
L
IPBT-1XX-XX-XX-D-XX
No OF POSITIONS
-02 THRU -15
(PER ROW)
-D: DOUBLE (USE IPBT-XX-D)
PLATING SPECIFICATION
LEAD STYLE
-H1: HIGH POWER, THRU HOLE
(USE T-1S55-XX-X-2, SEE FIG.1, SHEET 1)
-H2: HIGH POWER, SURFACE MOUNT
(USE T-1S55-02-X-2, SEE FIG.3, SHEET 3)
-H3: HIGH POWER. THRU HOLE, .670" STACKER
(USE T-1S55-05-X-2, SEE FIG.5, SHEET 4)
-H4: HIGH POWER. THRU HOLE, .748" STACKER
(USE T-1S55-06-X-2, SEE FIG.6, SHEET 4)
-H5: HIGH POWER. THRU HOLE, .787" STACKER
(USE T-1S55-07-X-2, SEE FIG.6, SHEET 4)
-H6: HIGH POWER. THRU HOLE, .984" STACKER
(USE T-1S55-08-X-2, SEE FIG.6, SHEET 4)
OPTION
-TM: MATTE TIN CONTACT AND TAIL
(USE T-1S55-XX-T-2)
-T: MATTE TIN CONTACT AND TAIL
(USE T-1S55-XX-T-2)
-02 (SEE SHEET 5, FIG.8)
-RA: RIGHT ANGLE (SEE FIG 2, SHEET 2)
[STYLE -H1 ONLY]
-GP: GUIDE POSTS (USE IPBT-XX-D-GP,
SEE FIG 4, SHEET 3)
(NOT AVAILABLE W/ -K OPTION)
*-K: KEYED POLARIZATION
(USE IPBT-XX-D-K)(SEE FIG 9, SHEET 5)
(NOT AVAILABLE W/ -GP OPTION)
*(LEAVE BLANK FOR NO KEY OPTION,
SAMTEC WILL ONLY SUPPORT EXISTING
BUSINESS AS OF REV W)
ROW SPECIFICATION
.260 6.60
REF
.424 10.77
REF
.510 12.95
REF
.045
SQ REF
1.14
2
MAX SWAY
.165 4.19
SECTION "A"-"A"
C
09
01
02
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01[.3]
2
.XXX:
.005[.13]
.XXXX:
.0020[.051]
MATERIAL:
.165 DOUBLE ROW TERMINAL ASSEMBLY
BY:
IPBT-1XX-XX-XX-D-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
DEAN P
7/27/2001
5
1
SHEET SCALE: 2:1
INSULATOR: LCP UL 94 VO, COLOR: BLACK
TERMINAL: HIGH COPPER ALLOY
F:\DWG\MISC\MKTG\IPBT-1XX-XX-XX-D-XX-MKT.SLDDRW
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. COPLANARITY (FOR SURFACE MOUNT): SEE TABLE 2 SHEET 3.
3. MAX BURR ALLOWANCE: .0015 [.038]
4. MINIMUM TERMINAL RETENTION: 1 LB.
5. IPBT-XX-D-XX AND IPBV-XX-D PARTS TO BE MOLDED TO POSITION,
IPBE-XX-XX-D ARE TO BE CUT.
6. MAX HEIGHT VARIATION BETWEEN PINS: .005 [.13]
7. ALL PIN TO PIN DIMENSIONS TO BE MEASURED FROM TIP TO TIP.
8. THIS NUMBER REPRESENTS THE NUMBER OF POSITIONS PER ROW ONLY
AND IS NOT INTENDED TO BE USED IN POSITION NUMBERING.
9. ALL PARTS TO BE PACKAGED IN TUBES EXCEPT 2 AND 3 POS. 2 AND 3 POS
PARTS TO BE LAYER PACKAGED.
10. MAX CUT FLASH: .005 [.13]
11. AFTER REVISION T OF COMPONENT PRINT IPT1-XX-D-XX-X, SAMTEC LOGO
TO APPEAR ON CORE #1 FOR POSITIONS 1 THROUH 5. FOR POSITIONS 6
THROUGH 15, LOGO TO APPEAR ON CORE #1 AND THE LAST CORE WITHIN THE SAME ROW.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
REVISION AC
