OMO ElectronicOMO Electronic
Expand menu
0 Cart

SE5007BT-R

P1-P3P4-P6P7-P9P10-P11
DATA SHEET
SE5007BT: 5 GHz Front-End Module with Power Detector
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202448A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 1
Applications
5 GHz WLAN (IEEE802.11a/g/n)
Access Points, PCMCIA, PC cards, Handhelds
Features
5GHz Front End Module with PA, LNA and T/R
Switch
Integrated power amplifier enable pin (VEN)
Buffered, temperature compensated power
detector
High and Low-Linearity mode
3% EVM, @17dBm, 64 QAM, 54 Mbps
30 dB Typical Gain
Lead Free and RoHS compliant, halogen free
package
16 pin 3 mm x 3 mm x 0.6 mm QFN, MSL1
Ordering Information
Part Number Package Remark
SE5007BT
16 Pin QFN
Samples
SE5007BT-R
16 Pin QFN
Tape and Reel
SE5007BT-
EK1
Evaluation Kit
Standard
Product Description
The SE5007BT is a 5GHz front end module offering
high linear power for wireless LAN applications. It
incorporates a power detector for control of the output
power.
The SE5007BT offers a high level of integration for a
simplified design, providing quicker time to market
and higher application board production yield. The
device integrates inter-stage match, a temperature
compensated, load insensitive power detector with
20dB of dynamic range, a 3.8GHz notch filter, a T/R
switch and an Rx LNA.
For wireless LAN applications, the device meets the
requirements of IEEE802.11a and delivers
approximately 17dBm of linear output power. It also
features a low linearity mode control to reduce current
consumption at low power modes.
The SE5007BT integrates the reference voltage
generator, allowing for a true 1.8V CMOS compatible
digital EN (enable) function to turn the power amplifier
on and off.
Functional Block Diagram
TXIN and ANT are DC Blocked. However external blocking cap is recommended for RX output.
Figure 1: Functional Block Diagram
Match &
Filter
Match
Bias, Enable, Detector Circuits
EN
TXIN
C0
C1
ANT
RX
H/L Lin
VPD
DATA SHEET
SE5007BT: 5 GHz Front-End Module with Power Detector
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202448A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 2
Pin Out Diagram
Figure 2: SE5007BT Pin-Out Diagram
Pin Out Description
Pin
No.
Name Description
Pin
No.
Name Description
1 EN PA Enable 9 VDD
LNA Supply Voltage (3.3V+/-10%
only)
2 GND Ground 10 GND Ground
3 RX 5GHz LNA Output Signal 11 ANT 5GHz Antenna output
4 GND Ground 12 GND Ground
5 TXIN 5GHz TX RF Input Signal 13 DET Power Detector Output
6 GND Ground 14 H/L Lin High-Low linearity Control
7 C0 Switch Control Logic 1 15 VCC1 Power Stage Supply Voltage
8 C1 Switch Control Logic 2 16 VCC2 Bias, Driver Stage Supply Voltage
DATA SHEET
SE5007BT: 5 GHz Front-End Module with Power Detector
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202448A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 3
Absolute Maximum Ratings
These are stress ratings only. Exposure to stresses beyond these maximum ratings for a long period of time may
cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the
recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this
device should be at ESD protected workstations.
Symbol Definition Min. Max. Unit
VCC1 Supply Voltage on pin 15 (VCC1) -0.3 4.8 V
VDD, VCC2 Supply Voltage on pins 9, 16 (VDD, VCC2) -0.3 3.6 V
EN DC input on Enable -0.3 3.6 V
TXIN RF Input Power, RFout into 50Ω match - 12 dBm
TSTG Storage Temperature Range -40 150 °C
ESD
HBM
JEDEC JESD22-A114
all pins
Antenna Pin - 1000
V
All Other Pins - 350
Recommended Operating Conditions
Symbol Parameter Min. Max. Unit
VCC1 Supply Voltage on pin 15 (VCC1) 3.0 4.5 V
VDD, VCC2 Supply Voltage on pins 9, 16 (VDD, VCC2) 3.0 3.6 V
TA Ambient Temperature -40 85 °C
Control Logic Characteristics
Conditions: VCC1
= V
CC2
= V
DD
= V
PAON = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5007T-
EV1 evaluation board, unless otherwise noted.
Symbol Parameter Conditions Min. Typ. Max. Unit
ICC-802.11a
Supply Current,
Transmit Mode
P
OUT
= 17 dBm, 54 Mbps, 64 QAM,
H/L Lin = 3.3V (High Linearity Mode)
- 195 -
mA
P
OUT
= 13 dBm, 54 Mbps, 64 QAM,
H/L Lin = 0V (Low Linearity Mode)
- 140 -
P
OUT
= 5 dBm, 54 Mbps, 64 QAM,
H/L Lin = 0V (Low Linearity Mode)
- 105 -
P
OUT
= 19 dBm, 54 Mbps, 64 QAM,
H/L Lin = 3.3V, VCC1 = 4.0V
220
Supply Current,
Receive Mode
VEN = C0 = 0V; C1 = 3.3V 15
VEN = C0 = C1 = 0V 0.02
IOFF Supply Current
V
EN = 0 V, No RF, C0=C1=0 V
Measured on VCC, VDD pins
- 20 50 μA
VENH Logic High Voltage - 1.6 - Vcc V
P1-P3P4-P6P7-P9P10-P11

SE5007BT-R

Mfr. #:
Buy SE5007BT-R
Manufacturer:
Skyworks Solutions, Inc.
Description:
RF Front End 5GHz FEM w/ Power Detector
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet