Pin configuration STOTG04E
4/26
(1) Input and open-drain output
(2) Input with internal pull-up resistor
(3) Internal regulator can be bypassed by connecting V
BAT
to this pin when the V
BAT
is in range of 2.7V to 3.6V
Figure 2. Functional diagram
20
V
BAT
Power Analog power supply voltage (+2.7V to +5.5V)
21 CAP1 I/O External capacitor pin for the charge pump
22 CAP2 I/O External capacitor pin for the charge pump
23 CGND Power Ground for the charge pump
24
V
IF
Power Logic power supply (+1.6V to 3.6V)
PlN N° SYMBOL I/O NAME AND FUNCTION
STOTG04E Maximum ratings
5/26
2 Maximum ratings
Table 2. Absolute maximum ratings
(*) In accordance to IEC61000-4-2, level 3.
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional Operation under these con-
ditions is not implied.
Table 3. Thermal data
Table 4. Recommended operating condition
Table 5. ESD Performance
Symbol Parameter Value Unit
V
IF
Logic Supply Voltage -0.5 to + 4.5 V
V
BAT
Analog Supply Voltage -0.5 to + 6.5 V
V
DCDIG
DC Input Voltage on any logic interface pin -0.5 to + 4.5 V
T
STG
Storage Temperature Range -65 to + 150 °C
V
ESD
Electrostatic discharge voltage
on USB pins
Human Body Model ± 8
kV
Contact Discharge (*) ± 6
Symbol Parameter Value Unit
R
thJA
Thermal Resistance Junction-Ambient 59 °C/W
Symbol Parameter Min. Typ. Max. Unit
V
IF
Logic Supply Voltage 1.6 1.8 3.6 V
V
BAT
Analog Supply Voltage 2.7 3.3 5.5 V
T
A
Operating Temperature Range -40 +85 °C
C
EXT
Charge pump external capacitor 100 220 470 nF
C
T
Charge pump tank capacitor 1 4.7 6.5 µF
C
TRM
Voltage regulator external capacitor 1 µF
R
S
Data lines impedance matching resistor 20
Symbol Parameter Value Unit
ESD
IEC-61000-4-2 (D+, D-, VBUS, ID)
Air discharge (10 pulses) ± 8
kV
Contact discharge (10 pulses) ± 6
IEC-61000-4-2 (other pins)
Air discharge (10 pulses) ± 2
Contact discharge (10 pulses) ± 2
Electrical characteristics STOTG04E
6/26
3 Electrical characteristics
Table 6. Electrical characteristics
Characteristics measured over recommended operating conditions unless otherwise is
noted. All typical values are referred to T
A
= 25°C, V
IF
= 1.8V, V
BAT
= 3.3V, R
S
= 20,
C
EXT
= 220nF, C
T
= 4.7µF and C
TRM
= 1µF
Symbol Parameter Test Conditions Min. Typ. Max. Unit
I
IF
Digital Part Supply Current
Active mode (1,2) 0.6 1.6 mA
Power down mode 1 µA
I
BAT
Operating Supply Current
Transceiver current while
transmitting and receiving (1, 2)
4.5 7
mA
Charge pump current, I
LOAD
= 8mA
17 25
Power down mode (4) 1 µA
LOGIC INPUTS AND OUTPUTS
V
OH
HIGH level output voltage
I
OH
= -100µA V
IF
-0.15
V
I
OH
= -2mA V
IF
-0.40
V
V
OL
LOW level output voltage
I
OL
= 100µA
0.15 V
I
OL
= 2mA
0.40 V
V
IH
HIGH level input voltage
0.7V
IF
V
V
IL
LOW level input voltage
0.3V
IF
V
I
LKG
Input leakage current -1 1 µA
I
OZ
Off-state output current -5 5 µA
V
BUS
V
BUS
V
BUS
output voltage I
LOAD
= 8mA
4.4 4.9 5.25 V
V
BUS_LKG
V
BUS
leakage voltage
No Load 3 200 mV
V
BUS_RIP
V
BUS
output ripple I
LOAD
= 8mA, C
T
= 4.7µF
30 60 mV
f
CP
Charge-pump switching
frequency (2)
0.5 0.8 1.5 MHz
R
VBUS
V
BUS
input impedance
40 76 100 k
I
VBUS
Maximum V
BUS
source current C
EXT
= 220 nF, V
BUS
> 4.4V
20 35 mA
V
BUS_VLD
V
BUS
valid comparator
threshold
Low to high transition 4.40
V
High to low transition 4.40
V
SES_VLD
Session valid comparator
threshold for both A and B
devices
Low to high transition 0.8 2.0
V
High to low transition 0.8 2.0
R
VBUS_PU
V
BUS
charge pull-up resistance
281 640
R
VBUS_PD
V
BUS
discharge pull-down
resistance
656 1260
ID
V
ID_BIAS
ID pin bias voltage
R
CP_ID
= 140kΩ, V
BAT
5V
1.3 1.9 3.0 V
R
ID_PU
ID pin pull-up resistance 70 105 130 k
R
ID_GND
ID line short resistance to detect id_gnd state 10
R
ID_FLOAT
ID line short resistance to detect id_float state 800 k

STOTG04EQTR

Mfr. #:
Manufacturer:
STMicroelectronics
Description:
USB Interface IC USB-OTG Full-speed Transceiver
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet