TS53YL503MR10

TS53
www.vishay.com
Vishay Sfernice
Revision: 12-Jan-17
1
Document Number: 51008
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
5 mm Square Surface Mount Miniature Trimmers Single-Turn
Cermet Sealed
The TS53 trimming potentiometer has been designed for
surface mount applications and offers volumetric efficiency
(5 mm x 5 mm x 2.7 mm) with high performance and
stability.
The TS53 design is suitable for both manual or automatic
operation, and can withstand wave, and reflow soldering
techniques.
FEATURES
0.25 W at 70 °C
For through hole version see T53Y series
Wide ohmic range (10 Ω to 1 MΩ)
Small size for optimum packaging density
Tests according to CECC 41000 or IEC 60393-1
Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
DIMENSIONS in millimeters (± 0.25 mm)
RECOMMENDED
SOLDERING AREAS
TS53YL TS53YJ TS53YL TS53YJ
Cruciform screwdriver slot
Ø 2.5, width 0.5
Deep: 0.55
Max. deep (center): 0.7
5
2.7
6.70
0.20
0.75
5
2.7
5.5
0.20
1.1
1.3
2
b
5.5
1.3
1.3
2.3
a
c
2
1.3
2
2
2.3
b
ac
4
A6
103
1 x 0.20
5
b
a
c
0.9 x 0.20
2.30
1 x 0.20
0.9 x 0.20
2.30
5
a
b
c
TS53
www.vishay.com
Vishay Sfernice
Revision: 12-Jan-17
2
Document Number: 51008
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ELECTRICAL SPECIFICATIONS
Resistive element Cermet
Electrical travel 220° ± 15°
Resistance range 10 Ω to 1 MΩ
Standard series 1 - 2 - 5
Tolerance standard ± 20 %
Circuit diagram
Power rating
linear 0.25 W at + 70 °C
Temperature coefficient See Standard Resistance Element Data table
Limiting element voltage (linear law) 200 V
Contact resistance variation (typical) 1 % or 3 Ω
End resistance (typical) 0.1 % or 3 Ω
Dielectric strength (RMS) 1000 V
Insulation resistance 1 GΩ
MECHANICAL SPECIFICATIONS
Mechanical travel 270 ° ± 10°
Operating torque (max. Ncm) 1.5
End stop torque (max. Ncm) 3.5
Unit weight (max. g) 0.15
Terminals Pure Sn (e3)
ENVIRONMENTAL SPECIFICATIONS
Temperature range -55 °C to +125 °C
Climatic category 55/125/56
Sealing Sealed container IP67
MSL level 4
SOLDERING RECOMMENDATIONS
Recommended reflow profile 2, see Application Note www.vishay.com/doc?52029
Caution
Reflow soldering must be done within 72 h while stored under a max. temperature of 30 °C, 60 % RH after opening the dry pack envelope.
a
(1)
b
(2)
c
(3)
cw
0
20
40 60
100 120 140
155
70
0.05
0
0.10
0.15
0.20
0.25
AMBIENT TEMPERATURE IN °C
POWER IN W
TS53
www.vishay.com
Vishay Sfernice
Revision: 12-Jan-17
3
Document Number: 51008
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
Nothing stated herein shall be construed as a guarantee of quality or durability.
RECOMMENDED METHOD OF STORAGE
Dry box storage is recommended as soon as the hermetic bag has been opened to prevent moisture absorption. The following conditions
should be observed, if dry boxes are not available:
Storage temperature 10 °C to 30 °C
Storage humidity 60 % RH max.
After more than 72 h under these conditions, moisture content will be too high for reflow soldering.
In case of moisture absorption, the devices will recover to the former condition by drying under the following condition:
192 h at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or
96 h at 60 °C + 5 °C and < 5 % RH for all device containers (not suitable for reel) or
24 h at 125 °C + 5 °C (not suitable for reel)
PERFORMANCES
TESTS CONDITIONS
TYPICAL VALUES AND DRIFTS
ΔR
T
/R
T
(%) ΔR
1-2
/R
1-2
(%) OTHER
Electrical endurance
1000 h at rated power
90'/30' - ambient temp. 70 °C
± 2 % ± 3 %
Contact resistance variation:
ΔR < 1 % Rn
Climatic sequence
Phase A dry heat 125 °C
Phase B damp heat
Phase C cold -55 °C
Phase D damp heat 5 cycles
± 2 % ± 3 %
Damp heat steady state
Temperature 40 °C - RH 93 %
56 days
± 2 % ± 3 %
Dielectric strength: 1000 V
RMS
Insulation resistance: > 10
4
MΩ
Charge of temperature -55 °C to +125 °C - 5 cycles ± 1 % ΔV
1-2
/V
1-3
± 2 %
Mechanical endurance 100 cycles - rated power ± (3 % + 5 Ω)
Shock
50 g - 11 ms
3 successive shocks in 3 directions
± 1 % ΔV
1-2
/V
1-3
± 1 %
Vibration
10 Hz to 55 Hz
0.75 mm or 10 g - 6 h
± 1 % ΔV
1-2
/V
1-3
± 1 %
STANDARD RESISTANCE ELEMENT DATA
STANDARD
RESISTANCE
VALUES
LINEAR LAW TYPICAL
TCR
- 55 °C
+ 125 °C
MAX. POWER
AT 70 °C
MAX. WORKING
VOLTAGE
MAX. CURRENT
THROUGH ELEMENT
Ω W V mA ppm/°C
10 0.25 1.58 158
± 100
20 0.25 2.24 112
50 0.25 3.54 71
100 0.25 5.00 50
200 0.25 7.07 35
500 0.25 11.2 22
1K 0.25 15.8 16
2K 0.25 22.4 11
5K 0.25 35.4 7
10K 0.25 50.0 5
20K 0.25 70.7 3.5
50K 0.25 112 2.2
100K 0.25 158 1.6
200K 0.20 200 1.0
500K 0.08 200 0.4
1M 0.04 200 0.2

TS53YL503MR10

Mfr. #:
Manufacturer:
Vishay
Description:
Trimmer Resistors - SMD 50Kohms 20% SQ POT
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union