IDT 89HPES32NT8BG2 Datasheet
4 of 35 December 17, 2013
Each of the two SMBus interfaces contain an SMBus clock pin and an SMBus data pin. In addition, the slave SMBus has the SSMBADDR2 pin. As
shown in Figure 2, the master and slave SMBuses may only be used in a split configuration. In the split configuration, the master and slave SMBuses
operate as two independent buses; thus, multi-master arbitration is not required. The SMBus master interface does not support SMBus arbitration. As
a result, the switch’s SMBus master must be the only master in the SMBus lines that connect to the serial EEPROM and I/O expander slaves.
Figure 2 Split SMBus Interface Configuration
Hot-Plug Interface
The PES32NT8BG2 supports PCI Express Hot-Plug on each downstream port. To reduce the number of pins required on the device, the
PES32NT8BG2 utilizes an external I/O expander, such as that used on PC motherboards, connected to the SMBus master interface. Following reset
and configuration, whenever the state of a Hot-Plug output needs to be modified, the PES32NT8BG2 generates an SMBus transaction to the I/O
expander with the new value of all of the outputs. Whenever a Hot-Plug input changes, the I/O expander generates an interrupt which is received on
the IOEXPINTN input pin (alternate function of GPIO) of the PES32NT8BG2. In response to an I/O expander interrupt, the PES32NT8BG2 generates
an SMBus transaction to read the state of all of the Hot-Plug inputs from the I/O expander.
General Purpose Input/Output
The PES32NT8BG2 provides 9 General Purpose I/O (GPIO) pins that may be individually configured as general purpose inputs, general purpose
outputs, or alternate functions. All GPIO pins are shared with other on-chip functions. These alternate functions may be enabled via software, SMBus
slave interface, or serial configuration EEPROM.
Processor
Switch
SSMBCLK
SSMBDAT
MSMBCLK
MSMBDAT
SMBus
Master
Other
SMBus
Devices
Serial
EEPROM
...
Hot-Plug
I/O
Expander
IDT 89HPES32NT8BG2 Datasheet
5 of 35 December 17, 2013
Pin Description
The following tables list the functions of the pins provided on the PES32NT8BG2. Some of the functions listed may be multiplexed onto the same
pin. The active polarity of a signal is defined using a suffix. Signals ending with an “N” are defined as being active, or asserted, when at a logic zero
(low) level. All other signals (including clocks, buses, and select lines) will be interpreted as being active, or asserted, when at a logic one (high) level.
Differential signals end with a suffix “N” or “P.” The differential signal ending in “P” is the positive portion of the differential pair and the differential signal
ending in “N” is the negative portion of the differential pair.
Note: Pin [x] of a port refers to a lane. For port 0, PE00RN[0] refers to lane 0, PE00RN[1] refers to lane 1, etc.
Signal Type Name/Description
PE00RN[3:0]
PE00RP[3:0]
I PCI Express Port 0 Serial Data Receive. Differential PCI Express receive pairs for
port 0.
PE00TN[3:0]
PE00TP[3:0]
O PCI Express Port 0 Serial Data Transmit. Differential PCI Express transmit pairs for
port 0.
PE02RN[3:0]
PE02RP[3:0]
I PCI Express Port 2 Serial Data Receive. Differential PCI Express receive pairs for
port 2.
PE02TN[3:0]
PE02TP[3:0]
O PCI Express Port 2 Serial Data Transmit. Differential PCI Express transmit pairs for
port 2.
PE04RN[3:0]
PE04RP[3:0]
I PCI Express Port 4 Serial Data Receive. Differential PCI Express receive pairs for
port 4.
PE04TN[3:0]
PE04TP[3:0]
O PCI Express Port 4 Serial Data Transmit. Differential PCI Express transmit pairs for
port 4.
PE06RN[3:0]
PE06RP[3:0]
I PCI Express Port 6 Serial Data Receive. Differential PCI Express receive pairs for
port 6.
PE06TN[3:0]
PE06TP[3:0]
O PCI Express Port 6 Serial Data Transmit. Differential PCI Express transmit pairs for
port 6.
PE08RN[3:0]
PE08RP[3:0]
I PCI Express Port 8 Serial Data Receive. Differential PCI Express receive pairs for
port 8.
PE08TN[3:0]
PE08TP[3:0]
O PCI Express Port 8 Serial Data Transmit. Differential PCI Express transmit pairs for
port 8.
PE12RN[3:0]
PE12RP[3:0]
I PCI Express Port 12 Serial Data Receive. Differential PCI Express receive pairs for
port 12.
PE12TN[3:0]
PE12TP[3:0]
O PCI Express Port 12 Serial Data Transmit. Differential PCI Express transmit pairs
for port 12.
PE16RN[3:0]
PE16RP[3:0]
I PCI Express Port 16 Serial Data Receive. Differential PCI Express receive pairs for
port 16.
PE16TN[3:0]
PE16TP[3:0]
O PCI Express Port 16 Serial Data Transmit. Differential PCI Express transmit pairs
for port 16.
PE20RN[3:0]
PE20RP[3:0]
I PCI Express Port 20 Serial Data Receive. Differential PCI Express receive pairs for
port 20.
PE20TN[3:0]
PE20TP[3:0]
O PCI Express Port 20 Serial Data Transmit. Differential PCI Express transmit pairs
for port 20.
Table 2 PCI Express Interface Pins
IDT 89HPES32NT8BG2 Datasheet
6 of 35 December 17, 2013
Signal Type Name/Description
GCLKN[1:0]
GCLKP[1:0]
I Global Reference Clock. Differential reference clock input pairs. This
clock is used as the reference clock by on-chip PLLs to generate the clocks
required for the system logic. The frequency of the differential reference
clock is determined by the GCLKFSEL signal.
Note: Both pairs of the Global Reference Clocks must be connected to and
derived from the same clock source. Refer to the Overview section of
Chapter 2 in the PES32NT8xG2 User Manual for additional details.
P00CLKN
P00CLKP
I Port Reference Clock. Differential reference clock pair associated with
port 0.
P02CLKN
P02CLKP
I Port Reference Clock. Differential reference clock pair associated with
port 2.
P04CLKN
P04CLKP
I Port Reference Clock. Differential reference clock pair associated with
port 4.
Table 3 Reference Clock Pins
Signal Type Name/Description
MSMBCLK I/O Master SMBus Clock. This bidirectional signal is used to synchronize transfers on the
master SMBus. It is active and generating the clock only when the EEPROM or I/O
Expanders are being accessed.
MSMBDAT I/O Master SMBus Data. This bidirectional signal is used for data on the master SMBus.
SSMBADDR[2] I Slave SMBus Address. This pin determines the SMBus address to which the slave
SMBus interface responds.
SSMBCLK I/O Slave SMBus Clock. This bidirectional signal is used to synchronize transfers on the
slave SMBus.
SSMBDAT I/O Slave SMBus Data. This bidirectional signal is used for data on the slave SMBus.
Table 4 SMBus Interface Pins

89H32NT8BG2ZBHLGI8

Mfr. #:
Manufacturer:
IDT
Description:
PCI Interface IC PCIE SWITCH
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union