91220-1 Datasheet 91220-1 | P1-P2

TE logo and Tyco Electronics are trademarks.

*Trademark. Other products, logos, and company names might be trademarks of their respective owners.

Instruction Sheet

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.tycoelectronics.com

1 of 2

LOC B

Figure 1

1. INTRODUCTION

Ribbon Cable Cutting Hand Tool 91220-1 is designed

to cut across ribbon cable (with solid or stranded

conductors) sizes 26 through 30 AWG at 90° to the

edge of the cable. Read these instructions thoroughly

before using the tool.

Dimensions in this instruction sheet are in metric

units [with U.S. customary units in brackets].

Figures are not drawn to scale.

Reasons for reissue of this instruction sheet are

provided in Section 6, REVISION SUMMARY.

2. DESCRIPTION

The tool consists of a handle with finger grips, a lock,

and two jaws with a replaceable blade and a

replaceable anvil. The anvil features an edge guide to

properly position the cable in the tool. The lock, in the

closed position, keeps the tool jaws closed when the

tool is NOT in use. See Figure 1.

3. USING THE TOOL

1. Rotate the lock to the opened position until the

tool jaws open fully.

2. Position the cable on the anvil with one edge of

the cable against the edge guide. See Figure 2.

3. Holding the cable in place, slide the cable

under the blade. Make sure that the end of the

cable is at least 1.59 mm [.062 in.] beyond the

blade. See Figure 2.

4. Hold the cable firmly on the anvil, and close

the tool handles until the cable is cut.

Figure 2

NOTE

Ribbon Cable Cutting

Hand Tool 91220-1

408-6574

10 MAY 10 Rev B

Blade

Anvil

Lock (Opened

Position)

Edge Guide

Jaw

End of Cable

Beyond Blade

Cable on Anvil with Edge

Against Edge Guide

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low

volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

408-6574

2 of 2

Rev B

5. Holding the handles closed, remove the cable

from the anvil.

6. When finished using the tool, close the

handles, and rotate the lock into the closed

position.

4. MAINTENANCE AND INSPECTION

4.1. Maintenance

The tool requires little maintenance other than to

keep it clean. Remove debris and contaminants from

the tool with a clean, soft, lint-free cloth or a clean,

soft brush. Do not use objects that could damage the

tool and do not use any solvents that could harm

paint or plastic material. When not in use, store the

tool in a clean, dry area.

4.2. Inspection

The tool should be inspected immediately upon

arrival at your facility and at regularly-scheduled

intervals thereafter to ensure that it has not been

damaged. Examine the tool for any signs of damage

or excessive wear during inspections. If replacement

of parts is necessary, refer to Figure 3 for the list of

customer-replaceable items.

5. REPLACEMENT

The parts listed in Figure 3 are customer-replaceable.

A complete inventory can be stocked and controlled

to prevent lost time when replacement of parts is

necessary. Order replacement parts through your

Representative, or call 1-800-526-5142, or send a

facsimile of your purchase order to 1-717-986-7605,

or write to:

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

6. REVISION SUMMARY

• Updated instruction sheet to corporate

requirements

Figure 3

REPLACEMENT PARTS

ITEM PART NUMBER DESCRIPTION QTY PER TOOL

1 606105-1 BLADE (Includes Roll Pin) 1

2 606106-1 ANVIL (Includes Screw) 1

50.8 mm [2.0 in.]

(Jaws Closed)

254 mm [10 in.]

40.64 mm

[1.60 in.]

19.05 mm

[.75 in.]

76.2 mm

[3.0 in.]

(Jaws

Closed)

P1-P2

91220-1

Mfr. #:

Buy 91220-1

Manufacturer:

TE Connectivity

Description:

Ribbon Cable Cutte

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet

91220-1