No.
Item Test Methods
Temperature Cycle6
The trimmer potentiometer shall be subjected to Table-4 temperature for 5 cycles. The trimmer potentiometer shall
be removed from the chamber, and maintained at a temperature of 25±5°C for 1~2 hours.
Specifications and Test Methods
Humidity7
1) PVC6, PV12, PV32, PV34 PVM4A---B01series
The trimmer potentiometer shall be placed in a chamber at a temperature of 40±2°C and a humidity of 90~95% with-
out loading for 250±8 hours. The trimmer potentiometer shall be removed from the chamber, and maintained at a
temperature of 25±5°C for 5±1/6 hours.
2) PVF2series
The trimmer potentiometer shall be placed in a chamber at 60±2°C and 90~95% without loading for 1000±12 hours.
The trimmer potentiometer shall be removed from the chamber, and maintained at a temperature of 25±5°C for
5±1/6 hours
2) PVG3, PVG5, PV01, PV22, PV23, PV36, PV37series
The trimmer potentiometer shall be subjected Figure-3 the programmed humidity environment for 10 cycle. The trim-
mer potentiometer shall be removed from the chamber, and maintained at a temperature of 25±5°C for 5±1/2 hours.
1
Vibration8
1) PV-- series
The trimmer potentiometer shall be vibrated throughout the frequency range at the 20G level. A complete frequency
range, 10Hz to 2000Hz and back, shall be made within 15 minutes for a total of 4 sweeps in each of the three axis
direction for a total of 12 sweeps.
2) PVF2 series
The trimmer potentiometer shall be subjected to vibration at 0.3 inch amplitude. The frequency shall be varied uni-
formly between the approximate limits of 10 Hz and 55Hz. This motion shall be applied for preiod of 2 hours in each
of 3 mutually perpendicular direction (total of 6 hours).
Sequence
Temp.
(°C)
PV-- series
PV22 series
PVF2 series
1
Table-4 One cycle of temperature cycle.
-55±3
-25±3
2
+25±2
Time (min.) 30 5 max.
3
+125±3
+150±3
+60±3
30
4
+25±2
5 max.
Continued from the preceding page.
INITIAL CONDITIONING
IN A DRY OVEN
24 HOURS
INITIAL MEASUREMENTS
AS SPECIFIED IN 3.2
CIRCULATION OF CONDITIONING AIR SHALL
BE AT A MINIMUM CUBIC RATE PER MINUTE
EQUIVALENT TO 5 TIMES THE VOLUME OF
THE CHAMBER
22 23 242120191817161514131211109876543210
70
65
60
55
50
45
40
35
30
25
20
15
10
5
-5
-10
0
ONE CYCLE 24 HOURS. REPEAT AS SPECIFIED IN 3.3
PRIOR TO FIRST CYCLE
UNLESS OTHERWISE
SPECIFIED
STEP 7STEP 6STEP 5STEP 4STEP 3STEP 2STEP 1
UNLESS OTHERWISE SPECIFIED
TEMPERATURE TOLERANCE IS,
±2°C AT ALL POINTS WITHIN THE
CHAMBER EXCEPT THE IMMEDIATE
VICINITY OF THE SPECIMENS AND
THE CHAMBER SURFACES
STEP 7a
STEPS 7a AND 7b PERFORMED DURING ANY
5 OF THE FIRST 9 CYCLES. HUMIDITY
UNCONTROLLED DURING STEPS 7a AND 7b
ONLY
VOLTAGE APPLIED AS SPECIFIED IN 3.5
STEP 7b
END OF FINAL CYCLE
MEASUREMENTS AS
SPECIFIED IN 3.6
+10°C
-2°C
HUMIDITY
UNCONTROLLED
RATE OF CHANGE OF TEMPERATURE IS UNSPECIFIED.
HOWEVER, SPECIMENS SHALL NOT BE SUBJECTED TO
RADIANT HEAT FROM CHAMBER-CONDITIONING
PROCESSES
90-98%RH
80-98%RH
90-98%RH
80-98%RH
90-98%RH
TEMPERTURE (DEGREES CELSIUS)
MIL-STD-202 METHOD 106
Figure-3
Shock9
1) PV-- series
The trimmer potentiometer shall be shocked at the 100G (50G for PV22 and PV23series) level and shall be subject-
ed to 4 shocks in each of the three axis direction for a total of 12 shocks.
2) PVM4A---B01series
The trimmer potentiometer shall be shocked at the 100G level and shall be subjected to 3 shocks in each of the six
axis direction for a total of 18 shocks.
Temperature Road Life10
Full rated continuous working voltage not exceeding the maximum rated voltage shall be applied intermittently
between the terminal #1 and the terminal #3 of the trimmer potentiometer, 1.5 hours on and 0.5 hours off, for a total
of 1000±12 hours, at a temperature of 70±2°C (85±2°C for PV01 and PV37series, 50±2°C for PVF2series). The trim-
mer potentiometer shall be removed from the chamber, and maintained at a temperature of 25±5°C for 1 to 2 hours.
High Temperature Exposure
(Except for PVF2)
11
The trimmer potentiometer shall be placed in a camber at a temperature of 125±3°C (150±3°C for PV12series)
250±8 hours without loading. The trimmer potentiometer shall be removed from the camber, and maintained at a
temperature of 25±5°C for 1 to 2 hours.
Low Temperature Exposure
(Except for PVF2 and
PVM4A---B01)
12
The trimmer potentiometer shall be placed in a camber at a temperature of -55±3°C for 1 hours without loading. Full
rated continuous working voltage not exceeding the maximum rated voltage shall be applied for 45 minutes. The
trimmer potentiometer shall be removed from the chamber, and maintained at a temperature of 25±5°C for approxi-
mately 24 hours.
Continued on the following page.
SMD Sealed Type/Lead Sealed Type Specifications and Test Methods
73
9
!Note
• Please read rating and !CAUTION (for storage and operating, rating, soldering and mounting, handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specification or transact the approval sheet for product specification before ordering.
Please read rating and !CAUTION (for storage and operating, rating, soldering and mounting, handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specification or to transact the approval sheet for product specificaion before ordering.
!Note
R50E12.pdf 02.9.5
