OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

BLM18KG601BH1D

P1-P3P4-P6P7-P9P10-P10
Spec. No. JENF243A-9129A-01 P.4/10
MURATA MFG.CO., LTD.
Reference Only
AEC-Q200
Murata Specification / Deviation
No. Stress Test Method
13 Mechanical Shock Per MIL-STD-202 Method 213
Condition F
1500g's (14.7N)/0.5ms/
Half sine
Meet Table Ｃ after testing.
Table Ｃ
14 Vibration 5g's(0.049N) for 20 minutes,
12cycles each of 3 orientations
T
est from 10-2000Hz.
Meet Table Ｃafter testing.
15 Resistance
to Soldering Heat
Solder temperature
260C+/-5 deg C
Immersion time 10s
Pre-heating:150C +/-10 deg,60s to 90s
Meet Table A after testing.
17 ESD Per AEC-Q200-002 Meet Table Ｃ after testing.
ESD Rank: Meet Item 3. (Rating)
18 Solderability Per J-STD-002
Method b : Not Applicable
95% of the terminations is to be soldered.
19 Electrical
Characterization
Measured : Impedance No defects
20 Flammability Per UL-94 Not Applicable
21 Board Flex Epoxy-PCB(1.6mm)
Deflection 2mm(min)
60s minimum holding tim
Meet TableＢafter testing.
22
T
erminal Strength Per AEC-Q200-006 No defects
30 Electrical
T
ransient
Conduction
Per ISO-7637-2 Not Applicable
8.Specification of Packaging
8-1.Appearance and Dimensions
(8mm-wide paper tape)
(in mm)
φ
1.5
1.1max.
Direction of feed
4.0±0.1
4.0±0.1
1.85±0.1
2.0±0.05
3.5±0.05
1.75±0.1
8.0±0.3
+0.1
-0
1.05±0.1
BLM18_BH：1.1 max.
BLM18_JH：0.85max.
Appearance No damage
Impedance
Change
(at 100MHz)
Within ±30%
DC Resistance Meet item 3.
Spec. No. JENF243A-9129A-01 P.5/10
MURATA MFG.CO., LTD.
Reference Only
(1) Taping
Products shall be packaged in the cavity of the base tape of 8mm-wide,4mm-pitch continuously
and sealed by top tape and bottom tape.
(2) The sprocket holes are to the right as the tape is pulled toward the user.
(3) Spliced point:The base tape and top tape have no spliced point
(4) Cavity:There shall not be burr in the cavity.
(5) Missing components number
Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater,
and are not continuous. The specified quantity per reel are kept.
8-2.Tape Strength
(1)Pull Strength
Top tape
5N min.
Bottom tape
(2)Peeling off force of Top tape
0.1N to 0.6N (Minimum value is typical.)
*Speed of Peeling off:300mm/min
8-3.Taping Condition
(1)Standard quantity per reel
Quantity per 180mm reel: 4000 pcs. / reel
(2)There shall be leader-tape (top tape and empty tape ) and trailer- tape(empty tape) as follows.
(3)On paper tape, the top tape and the base tape shall not be adhered at the tip of the empty leader tape
for more than 5 pitch.
(4)Marking for reel
The following items shall be marked on a label and the label is stuck on the reel.
(Customer part number, MURATA part number, Inspection number(∗1) , RoHS marking (∗2) , Quantity, etc)
∗1) « Expression of Inspection No. » □□
OOOO ×××
(1) (2) (3)
(1)
Factory Code
(2) Date First digit : Year / Last digit of year
Second digit : Month / Jan. to Sep. → 1 to 9, Oct. to Dec. → O, N, D
Third, Fourth digit : Day
(3) Serial No.
∗2) « Expression of RoHS marking » ROHS – Y
(△)
(1) (2)
(1)
RoHS regulation conformity parts.
(2) MURATA classification number
(5)Outside package
These reels shall be packed in the corrugated cardboard package and the following items shall be marked
on a label and the label is stuck on the box.
(Customer name, Purchasing order number, Customer part number, MURATA part number,
RoHS discrimination(∗2) ,Quantity, etc)
(6)Dimensions of reel and taping(leader-tape, trailer-tape)
(in mm)
Top tape
Bottom tape
Base tape
165 to 180 degree
F
Empty tape
190 min.
Leader
Trailer
2.0±0.5
φ
13.0±0.2
φ
21.0±0.8
φ
180
φ
60
9.0
13.0±1.4
+1
-
0
+0
-3
Direction of feed
210 min.
160 min.
Top tape
+1
-0
Label
Spec. No. JENF243A-9129A-01 P.6/10
MURATA MFG.CO., LTD.
Reference Only
8-4. Specification of Outer Case
Outer Case Dimensions
(mm)
Standard Reel Quantity in Outer Case
(Reel)
W D H
186 186 93 5
∗ Above Outer Case size is typical. It depends on a quantity of an order.
9. Caution
9-1.Rating
Do not use products beyond the Operating Temperature Range and Rated Current.
9-2.Surge current
Excessive surge current (pulse current or rush current) than specified rated current applied to the product
may cause a critical failure, such as an open circuit, burnout caused by excessive temperature rise.
Please contact us in advance in case of applying the surge current.
9-3.Fail Safe
Be sure to provide an appropriate fail-safe function on your product to prevent from a second damage
that may be caused by the abnormal function or the failure of our products.
9-4.Limitation of Applications
Please contact us before using our products for the applications listed below which require especially high
reliability for the prevention of defects which might directly cause damage to the third party's life, body or property.
(1)Aircraft equipment (6)Disaster prevention / crime prevention equipment
(2)Aerospace equipment (7)Traffic signal equipment
(3)Undersea equipment (8)Transportation equipment (trains,ships,etc.)
(4)Power plant control equipment (9)Applications of similar complexity and /or reliability requirements
(5)Medical equipment to the applications listed in the above
10. Notice
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
10-1.Land pattern designing
• Standard land dimensions
< For BLM18 series >
Type
Rated
Current
(A)
ab c
Land pad thickness
and dimension d
18µm 35µm 70µm
BLM18
~1.0
0.7
Flow
2.2 to 2.6
Reflow
1.8 to 2.0
0.7
0.7 0.7 0.7
~1.5
1.2 0.7 0.7
~2.5
2.4 1.2 0.7
~4.0
6.4 3.3 1.65
(in mm)
∗The excessive heat by land pads may cause deterioration
at joint of products with substrate.
a
b
Chip Ferrite Bead
Solder Resist
Pattern
d
c
W
D
Label
H
P1-P3P4-P6P7-P9P10-P10

BLM18KG601BH1D

Mfr. #:
Buy BLM18KG601BH1D
Manufacturer:
Murata Electronics
Description:
Ferrite Beads 600ohm 1.0A 0.15ohm AEC-Q200
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet