OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

MAX4563CEE+

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P16
MAX4562/MAX4563
Serially Controlled, Clickless
Audio/Video Switches
4 _______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS—Single +3V Supply (continued)
(V+ = +3V ±10%, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at T
A
= +25°C.) (Note 2)
ns
T
A
= +25°C
T
A
= +25°C
T
A
= T
MIN
to T
MAX
-10 10
T
A
= T
MIN
to T
MAX
CONDITIONS
COM _ On-Leakage
Current (Notes 6, 10)
I
COM
_
(ON)
V
COM_
= 3V, 0.5V;
V
NO
_ _ = 3V, 0.5V,
or floating;
V+ = 3.6V
-1 0.002 1
nA
Total Harmonic Distortion
plus Noise
THD+N
f
IN
= 1kHz, V
NO
_ _ =
0.5V
RMS
, V
NO_ _
= 1.5V
0.1
%
Off-Isolation (Note 7) V
ISO(A)
V
NO_ _
= 0.5V
RMS
, f
IN
= 20kHz, R
L
= 600Ω,
Figure 1
80 dB
Channel-to-Channel Crosstalk V
CT(A)
V
NO_ _
= 0.5V
RMS
, f
IN
= 20kHz, R
S
= 600Ω,
Figure 1
85 dB
UNITSMIN TYP MAXSYMBOLPARAMETER
Off-Isolation (Note 7) V
ISO(V)
V
NO_ _
= 0.5V
RMS
, f
IN
= 10MHz, R
L
= 50Ω,
Figure 1
-50 dB
Channel-to-Channel Crosstalk V
CT(V)
V
NO_ _
= 0.5V
RMS
, f
IN
= 10MHz, R
S
= 50Ω,
Figure 1
-55 dB
-3dB Bandwidth BW R
SOURCE
= 50Ω, R
L
= 50Ω 200 MHz
Off-Capacitance C
OFF(NO)
f
IN
= 1MHz 10 pF
Turn-On Time t
ONSD
V
NO_ _
= 1.5V,
R
L
= 5kΩ, C
L
= 35pF
400 800
ns
1000
T
A
= +25°C
T
A
= T
MIN
to T
MAX
8
On-Resistance
Flatness (Note 5)
R
FLAT
I
COM_
= 4mA;
V
NO_ _
= 1V, 1.5V, 2V;
V
+ = 2.7V
36
Ω
T
A
= +25°C
T
A
= T
MIN
to T
MAX
Turn-Off Time t
OFFSD
V
NO_ _
= 1.5V,
R
L
= 300Ω, C
L
= 35pF
200 350
500
V
NO_ _
= 1.5V, T
A
= T
MIN
to T
MAX
Break-Before-Make Time t
BBM
10 100 ns
V
NO_ _
= 1.5V, R
L
= 5kΩ, C
L
= 35pFTurn-On Time t
ONSE
12 ms
V
NO_ _
= 1.5V, R
L
= 300Ω, C
L
= 35pFTurn-Off Time t
OFFSE
3 ms
T
A
= +25°C
T
A
= T
MIN
to T
MAX
-10 10
COM_ Off-Leakage
Current (Notes 6, 10)
I
COM
_
(OFF)
V
COM
_ = 0.5V, 3V;
V
NO_ _
= 3V, 0.5V;
V+ = 3.6V
-1 0.001 1
nA
T
A
= +25°C
T
A
= T
MIN
to T
MAX
-10 10
NO_ _ Off-Leakage
Current (Notes 6, 10)
I
NO_ _(OFF)
V
COM
_ = 0.5V, 3V;
V
NO_ _
= 3V, 0.5V;
V+ = 3.6V
-1 0.001 1
nA
R
L
= 600Ω
AUDIO PERFORMANCE
VIDEO PERFORMANCE
DYNAMIC TIMING WITH CLICKLESS MODE DISABLED (Notes 8, 12, and Figure 2)
DYNAMIC TIMING WITH CLICKLESS MODE ENABLED (Notes 8, 12, and Figure 2)
R
L
= 10kΩ 0.01
MAX4562/MAX4563
Serially Controlled, Clickless
Audio/Video Switches
_______________________________________________________________________________________ 5
pF5f = 1MHzC
IN
Input Capacitance
V0.2V
HYST
Input Hysteresis
UNITSMIN TYP MAXCONDITIONSSYMBOLPARAMETER
µA-1 0.001 1Digital inputs = 0 or V+I
LEAK
Input Leakage Current
V+ = 3V
V+ = 3V 0.6
2
V
3V+ = 5V
V
IH
Input High Voltage
V
0.8V+ = 5V
V
IL
Input Low Voltage
VV+ - 0.5 I
SOURCE
= 0.5mAV
OH
DOUT Output High Voltage
I/O INTERFACE CHARACTERISTICS
(V+ = +2.7V to +5.25V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at T
A
= +25°C.)
2-WIRE TIMING CHARACTERISTICS
(Figure 3, V+ = +2.7V to +5.25V, f
SCL
= 100kHz, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at T
A
= +25°C.)
V0.4I
SINK
= 6mAV
OL
Output Low Voltage
DIGITAL INPUTS (SCLK, DIN, CS, SCL, SDA, A0, A1)
DIGITAL OUTPUTS (DOUT, SDA)
UNITSMIN TYP MAXCONDITIONSSYMBOLPARAMETER
ns050Pulse Width of Suppressed Spike
ns
20 +
300
0.1C
b
t
R
SCL/SDA Rise Time
µs4.0t
HIGH
Clock High Period
µs4.7t
LOW
Clock Low Period
ns250t
SU:DAT
Data Setup Time
µs0t
HD:DAT
Data Hold Time
µs4.0t
SU:STO
Stop Condition Setup Time
µs4.7t
BUF
Bus Free Time between Stop
and Start Conditions
0 100V+ = 2.7V to 5.25V
f
SCL
SCL Clock Frequency
ns
20 +
300
0.1C
b
t
F
SCL/SDA Fall Time
µs4.0The first clock is generated after this period t
HD:STA
Hold Time After Start Condition
kHz
400V+ = 4.75V to 5.25V
MAX4562/MAX4563
Serially Controlled, Clickless
Audio/Video Switches
6 _______________________________________________________________________________________
Note 2: The algebraic convention is used in this data sheet; the most negative value is shown in the minimum column.
Note 3: Guaranteed by design. Not subject to production testing.
Note 4: ∆R
ON
= R
ON(MAX)
- R
ON(MIN)
.
Note 5: Resistance flatness is defined as the difference between the maximum and minimum on-resistance values, as measured
over the specified analog signal range.
Note 6: Leakage parameters are 100% tested at maximum rated temperature and guaranteed by correlation at T
A
= +25°C.
Note 7: Off-isolation = 20 log (V
COM
_ / V
NO
_ _ ), V
COM
_ = output, V
NO
_ _ = input to off switch.
Note 8: All timing is measured from the clock’s falling edge preceding the ACK signal for 2-wire and from the rising edge of CS for
3-wire. Turn-off time is defined at the output of the switch for a 0.5V change, tested with a 300Ω load to ground. Turn-on
time is defined at the output of the switch for a 0.5V change and measured with a 5kΩ load resistor to GND. All timing is
shown with respect to 20% V+ and 70% V+, unless otherwise noted.
Note 9: Supply current can be as high as 2mA per switch during switch transitions in the clickless mode, corresponding to a 12mA
total supply transient current requirement.
Note 10: Leakage testing is guaranteed by testing with a +5.25V supply.
Note 11: C
b
= capacitance of one bus line in pF. Tested with C
b
= 400pF.
Note 12: Typical values are for MAX4563 devices.
15
19
17
21
27
29
25
23
31
012345
ON-RESISTANCE vs. COM_ VOLTAGE
MAX4562 otc01
V
COM
_ (V)
ON-RESISTANCE (Ω)
V+ = 2.7V
V+ = 3.3V
V+ = 5.0V
12
14
13
16
15
17
18
20
19
21
012345
ON-RESISTANCE vs. COM_ VOLTAGE
AND TEMPERATURE
MAX4562 TOC02
V
COM_
(V)
ON-RESISTANCE (Ω)
T
A
= +70°C
T
A
= +85°C
T
A
= +25°C
T
A
= -40°C
0.1
1
100
10
1000
-40 -15 10 35 60 85
LEAKAGE CURRENT vs. TEMPERATURE
MAX4562/3toc03
TEMPERATURE (°C)
CURRENT (pA)
COM_ON
NO_ _OFF
COM_OFF
Typical Operating Characteristics
(V+ = +5V, T
A
= +25°C, unless otherwise noted.)
3-WIRE TIMING CHARACTERISTICS
(Figure 5, V+ = +2.7V to +5.25V, f
OP
= 2.1MHz, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are at T
A
= +25°C.)
SCLK Pulse Width High t
CH
200
V+ = 4.75V to 5.25V 10
ns
Fall Time (SCLK, DIN, CS)
t
F
2 µs
SCLK Pulse Width Low t
CL
200 ns
CS Fall to SCLK Rise Hold
t
CSH
0 ns
Rise Time (SCLK, DIN, CS)
t
R
DIN to SCLK Setup t
DS
100 ns
Operating Frequency f
OP
V+ = 2.7V to 5.25V 0 2.1
MHz
DIN to SCLK Hold t
DH
0 ns
2 µs
CS Fall to SCLK Rise Setup
t
CSS
100 ns
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
CS Pulse Width High
t
CSW
40 ns
SCLK Fall to Output Data Valid t
DO
C
LOAD
= 50pF 200 ns
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P16

MAX4563CEE+

Mfr. #:
Buy MAX4563CEE+
Manufacturer:
Maxim Integrated
Description:
Video Switch ICs Clickless A/V Switch
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet