4
OFF Isolation R
L
= 50, C
L
= 15pF, f = 100kHz,
V
NO
or V
NC
= 1V
RMS
, (See Figures 4 and 6)
25 - >90 - dB
Crosstalk, (Note 9) 25 - <-90 - dB
POWER SUPPLY CHARACTERISTICS
Power Supply Range Full 2-6V
Positive Supply Current, I+ V
S
= 5.5V, V
IN
= 0V or V+, Switch On or Off 25 -1 0.05 1 A
Full -1 - 1 A
Negative Supply Current, I- 25 -1 0.05 1 A
Full -1 - 1 A
NOTES:
5. V
IN
= Input voltage to perform proper function.
6. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
7. Leakage parameter is 100% tested at high temp, and guaranteed by correlation at 25
o
C.
8. Flatness is defined as the delta between the maximum and minimum R
ON
values over the specified voltage range.
9. Between any two switches.
Electrical Specifications 5V Supply Test Conditions: V+ = +4.5V to +5.5V, V- = GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 5),
Unless Otherwise Specified
PARAMETER TEST CONDITIONS
TEMP
(
o
C)
MIN
(NOTE 6) TYP
MAX
(NOTE 6)UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 - V+ V
ON Resistance, R
ON
V+ = 4.5V, I
COM
= 1.0mA, V
NO
or V
NC
= 3.5V
(Figure 5)
25 - 125 200
Full - - 250
R
ON
Matching Between Channels,
R
ON
V+ = 5V, I
COM
= 1.0mA, V
NO
or V
NC
= 3.5V 25 - 2 8
Full - - 10
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
V+ = 5.5V, V
COM
= 1V, 4.5V, V
NO
or V
NC
= 4.5V, 1V
(Note 7)
25 -1 0.01 1 nA
Full -10 - 10 nA
COM OFF Leakage Current,
I
COM(OFF)
V+ = 5.5V, V
COM
= 1V, 4.5V, V
NO
or V
NC
= 4.5V, 1V
(Note 7)
25 -1 0.01 1 nA
Full -10 - 10 nA
COM ON Leakage Current,
I
COM(ON)
V+ = 5.5V, V
COM
= 1V, 4.5V (Note 7) 25 -2 - 2 nA
Full -20 - 20 nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, V
INH
Full - 1.6 2.4 V
Input Voltage Low, V
INL
Full 0.8 1.6 - V
Input Current, I
INH
, I
INL
V+ = 5.5V, V
IN
= 0V or V+ Full -1 0.03 1 A
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 4.5V, V
NO
or V
NC
= 3V, R
L
= 300, C
L
= 35pF,
V
IN
= 0 to 3V (Figure 1)
25 - 60 100 ns
Full - - 150 ns
Turn-OFF Time, t
OFF
V+ = 4.5V, V
NO
or V
NC
= 3V, R
L
= 300, C
L
= 35pF,
V
IN
= 0 to 3V (Figure 1)
25 - 20 50 ns
Full - - 75 ns
Break-Before-Make Time Delay
(ISL84523), t
D
V+ = 5.5V, V
NO
or V
NC
= 3V, R
L
= 300, C
L
= 35pF,
V
IN
= 0 to 3V (Figure 3)
25 10 30 - ns
Charge Injection, Q C
L
= 1.0nF, V
G
= 0V, R
G
= 0Figure 2) 25 - 1 5 pC
Electrical Specifications +5V Supply Test Conditions: V
SUPPLY
= 4.5V to 5.5V, GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 5),
Unless Otherwise Specified (Continued)
PARAMETER TEST CONDITIONS
TEMP
(
o
C)
(NOTE 6)
MIN TYP
(NOTE 6)
MAX UNITS
ISL84521, ISL84522, ISL84523
