6.42
IDT7006S/L
High-Speed 16K x 8 Dual-Port Static RAM Military, Industrial and Commercial Temperature Ranges
9
NOTES:
1. Transition is measured 0mV from Low or High-impedance voltage with load (Figure 2).
2. This parameter is guaranteed by device characterization, but is not production tested but not tested.
3. To access RAM, CE = V
IL, SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. Either condition must be valid for the entire tEW time.
4. The specification for t
DH must be met by the device supplying write data to the RAM under all operating conditions. Although tDH and tOW values will vary over voltage
and temperature, the actual t
DH will always be smaller than the actual tOW.
5. 'X' in part numbers indicates power rating (S or L).
AC Electrical Characteristics Over the
Operating Temperature and Supply Voltage
(5)
Symbol Parameter
7006X15
Com'l Only
7006X17
Com'l Only
7006X20
Com'l, Ind
& Military
7006X25
Com'l &
Military
UnitMin. Max. Min. Max. Min. Max. Min. Max.
WRITE CYCLE
t
WC
Write Cycle Time 15
____
17
____
20
____
25
____
ns
t
EW
Chip Enable to End-of-Write
(3)
12
____
12
____
15
____
20
____
ns
t
AW
Address Valid to End-of-Write 12
____
12
____
15
____
20
____
ns
t
AS
Address Set-up Time
(3)
0
____
0
____
0
____
0
____
ns
t
WP
Write Pulse Width 12
____
12
____
15
____
20
____
ns
t
WR
Write Recovery Time 0
____
0
____
0
____
0
____
ns
t
DW
Data Valid to End-of-Write 10
____
10
____
15
____
15
____
ns
t
HZ
Output High-Z Time
(1,2)
____
10
____
10
____
12
____
15 ns
t
DH
Data Hold Time
(4)
0
____
0
____
0
____
0
____
ns
t
WZ
Write Enable to Output in High-Z
(1,2)
____ ____ ____ ____ ____
12
____
15 ns
t
OW
Output Active from End-of-Write
(1, 2 ,4 )
0
____
0
____
0
____
0
____
ns
t
SWRD
SEM Flag Write to Read Time
5
____
5
____
5
____
5
____
ns
t
SPS
SEM Flag Contention Window
5
____
5
____
5
____
5
____
ns
2739 tbl 14a
Symbol Parameter
7006X35
Com'l & Military
7006X55
Com'l, Ind
& Military
7006X70
Military
Only
UnitMin. Max. Min. Max. Min. Max.
WRITE CYCLE
t
WC
Write Cycle Time 35
____
55
____
70
____
ns
t
EW
Chip Enable to End-of-Write
(3)
30
____
45
____
50
____
ns
t
AW
Address Valid to End-of-Write 30
____
45
____
50
____
ns
t
AS
Address Set-up Time
(3)
0
____
0
____
0
____
ns
t
WP
Write Pulse Width 25
____
40
____
50
____
ns
t
WR
Write Recovery Time 0
____
0
____
0
____
ns
t
DW
Data Valid to End-of-Write 15
____
30
____
40
____
ns
t
HZ
Output High-Z Time
(1,2)
____
15
____
25
____
30 ns
t
DH
Data Hold Time
(4)
0
____
0
____
0
____
ns
t
WZ
Write Enable to Output in High-Z
(1,2)
____
15
____
25
____
30 ns
t
OW
Output Active from End-of-Write
(1, 2 ,4 )
0
____
0
____
0
____
ns
t
SWRD
SEM Flag Write to Read Time
5
____
5
____
5
____
ns
t
SPS
SEM Flag Contention Window
5
____
5
____
5
____
ns
2739 tbl 14b