NOTES: (UNLESS OTHERWISE SPECIFIED)
1. ALL DIMENSIONS ARE IN INCHES [mm].
2. DIMENSIONS APPLY AFTER FINISHING.
3. MANUFACTURE TO BE COMPLIANT WITH EU RoHS DIRECTIVE.
4. SAFETY BREAK ALL SHARP CORNERS AND EDGES .02 MAXIMUM.
SHEET 1 OF 1
LDCFDLT_A
SCALE: 2:1
TITLE:
SIZE
DWG. NO.
REV
DO NOT SCALE DRAWING
ANGLES:
1
TOLERANCES:
.020 [0.50]-.200 [5.00]=
.008 [0.20]
.200 [5.00]-1.200 [30.00]=
.016 [0.40]
1.20 [30.0]-4.75 [120.0]=
.024 [0.60]
4.75 [120.0]-12.40 [315.0]=
.040 [1.0]
DRAWN:
ENGR:
DT:
DT:
MATERIAL:
FINISH:
PROJECTION:
:
THIS DRAWING CONTAINS PROPRIETARY INFORMATION
THAT IS THE SOLE PROPERTY OF LINX TECHNOLOGIES, AND SHALL BE
TREATED AS SUCH. NO DISCLOSURE OR REPRODUCTION OF THIS
DOCUMENT IS PERMITTED, IN WHOLE OR IN PART, WITHOUT THE
EXPRESS WRITTEN PERMISSION OF LINX TECHNOLOGIES OR ITS
DESIGNATED AGENTS.
159 ORT LANE
MERLIN, OR 97532
SMA MALE RIGHT ANGLE
CABLE END CRIMP FOR RG58 CABLE
CONSMA012-R58
B
2-JUL-12
B.MURPHY
1/4-36UNS-2B
THREADS
S.HOGAN
2-JUL-12
RECOMMENDED CABLE STRIPPING DIMENSIONS
Descripon Material Finish
Body
Pin
Insulaon
Nickel
N/A
Gold
PTFE
Brass
Brass
Washer BE CU Nickel
Gasket RubberSI Rubber
Crimp Ring NickelBrass
Insulator N/APTFE
Cover NickelBrass
PolyolefinHeat Shrink Black
BARREL
0.276
[7.00]
0.287
[7.30]
0.650
[16.50]
0.331
[8.40]
0.287
[7.30]
Ø0.260
[6.60]
SIDE VIEW
INSULATORCOVER
Ø0.185
[4.70]
Ø0.146
[3.70]
0.055
[1.40]
0.051
[1.30]
0.500
[12.70]
Ø0.256
[6.50]
CRIMP RING
Ø0.287
[7.30]
0.984
[25.00]
HEAT SHRINK
0.197
[5.00]
0.181
[4.60]
0.098
[2.50]
RG-58 Cable
BRAIDED SHIELD
CONSMA012-R58 ASSEMBLY INSTRUCTIONS
1. Strip cable to recommended dimensions.
2. Slip heat shrink and crimp ring onto stripped cable.
2. Slide the cable into the body until the center conductor
is centered in the fork.
3. Push the braided shield over the barrel.
4. Solder the center conductor into the center of the fork.
5. Slide the crimp ring over the shield and crimp with a 0.213”
hex crimp tool (or one labeled for use with RG-58 cable).
6. Trim off any excess shield wire sticking out from the ring.
7. Slip the heat shrink over the crimp ring until it is against
the body and shrink.
8. Insert insulator into body.
9. Push the cover into the opening.
Ø0.124
[3.15]
Ø0.177
[4.50]
REVISIONS
REV
DESCRIPTION
DATE
APPV
B
Added new title block, heat shrink and instructions;
updated cover and insulator drawings
2-JUL-12 SAH
