OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

74LVTH2245PW,112

P1-P3P4-P6P7-P9P10-P12P13-P15
Nexperia
74LVT2245; 74LVTH2245
3.3 V octal transceiver with 30 Ω termination resistors; 3-state
74LVT_LVTH2245 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2017. All rights reserved.
Product data sheet Rev. 5 — 10 April 2017
4 / 15
7 Limiting values
Table 4. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions Min Max Unit
V
CC
supply voltage -0.5 +4.6 V
V
I
input voltage
[1]
-0.5 +7.0 V
V
O
output voltage output in OFF-state or HIGH-state
[1]
-0.5 +7.0 V
I
IK
input clamping current V
I
< 0 V -50 - mA
I
OK
output clamping current V
O
< 0 V -50 - mA
output in LOW-state - 128 mAI
O
output current
output in HIGH-state -64 - mA
T
stg
storage temperature -65 +150 °C
T
j
junction temperature
[2]
- 150 °C
P
tot
total power dissipation T
amb
= -40 to +85 °C
[3]
500 mW
[1] The input and output negative voltage ratings may be exceeded if the input and output clamp current ratings are observed.
[2] The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction temperatures which
are detrimental to reliability.
[3] For SO20 package: above 70 °C derate linearly with 8 mW/K.
For (T)SSOP20 package: above 60 °C derate linearly with 5.5 mW/K.
8 Recommended operating conditions
Table 5. Recommended operating conditions
Symbol Parameter Conditions Min Typ Max Unit
V
CC
supply voltage 2.7 - 3.6 V
V
I
input voltage 0 - 5.5 V
I
OH
HIGH-level output current -12 - - mA
I
OL
LOW-level output current - - 12 mA
Δt/ΔV input transition rise and fall rate outputs enabled - - 10 ns/V
T
amb
ambient temperature in free-air -40 +25 +85 °C
9 Static characteristics
Table 6. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions Min Typ
[1]
Max Unit
T
amb
= -40 °C to +85 °C
V
IK
input clamping voltage V
CC
= 2.7 V; I
IK
= -18 mA -1.2 -0.9 - V
V
IH
HIGH-level input voltage 2.0 - - V
V
IL
LOW-level input voltage - - 0.8 V
V
OH
HIGH-level output voltage V
CC
= 3.0 V; I
OH
= -12 mA 2.0 2.2 - V
Nexperia
74LVT2245; 74LVTH2245
3.3 V octal transceiver with 30 Ω termination resistors; 3-state
74LVT_LVTH2245 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2017. All rights reserved.
Product data sheet Rev. 5 — 10 April 2017
5 / 15
Symbol Parameter Conditions Min Typ
[1]
Max Unit
V
OL
LOW-level output voltage V
CC
= 3.0 V; I
OL
= 12 mA - - 0.8 V
control pins
V
CC
= 0 V or 3.6 V; V
I
= 5.5 V - 1 10 μA
V
CC
= 3.6 V; V
I
= V
CC
or GND - ±0.1 ±1 μA
I/O data pins; V
CC
= 3.6 V
[2]
V
I
= 5.5 V - 1 20 μA
V
I
= V
CC
- 0.1 1 μA
I
I
input leakage current
V
I
= 0 V - -1 -5 μA
I
OFF
power-off leakage current V
CC
= 0 V; V
I
or V
O
= 0 V to 4.5 V - 1 ±100 μA
I
BHL
bus hold LOW current V
CC
= 3 V; V
I
= 0.8 V 75 150 - μA
I
BHH
bus hold HIGH current V
CC
= 3 V; V
I
= 2.0 V - -150 -75 μA
I
BHLO
bus hold LOW overdrive current V
CC
= 0 V to 3.6 V; V
I
= 3.6 V
[3]
- - 500 μA
I
BHHO
bus hold HIGH overdrive current V
CC
= 0 V to 3.6 V; V
I
= 3.6 V
[3]
-500 - - μA
I
CEX
output high leakage current output in HIGH-state when V
O
> V
CC
;
V
O
= 5.5 V; V
CC
= 3.0 V
- 60 125 μA
I
O(pu/pd)
power-up/power-down output current V
CC
≤ 1.2 V; V
O
= 0.5 V to V
CC
;
V
I
= GND or V
CC
; OE = don’t care
[4]
- 15 ±100 μA
V
CC
= 3.6 V; V
I
= GND or V
CC
; I
O
= 0 A
outputs HIGH - 0.13 0.19 mA
outputs LOW - 3 12 mA
I
CC
supply current
outputs disabled
[5]
- 0.13 0.19 mA
ΔI
CC
additional supply current per input pin; V
CC
= 3 V to 3.6 V;
one input at V
CC
- 0.6 V; other inputs at
V
CC
or GND
[6]
- 0.1 0.2 mA
C
I
input capacitance DIR and OE; V
I
= 0 V or 3.0 V - 4 - pF
C
I/O
input/output capacitance An and Bn; outputs disabled;
V
I/O
= 0 V or 3.0 V
- 10 - pF
[1] Typical values are measured at V
CC
= 3.3 V and T
amb
= 25 °C.
[2] Unused pins at V
CC
or GND.
[3] This is the bus hold overdrive current required to force the input to the opposite logic state.
[4] This parameter is valid for any V
CC
between 0 V and 1.2 V with a transition time of up to 10 ms. From V
CC
= 1.2 V to V
CC
= 3.0 V to 3.6 V a transition time
of 100 μs is permitted.
[5] I
CC
is measured with outputs pulled to V
CC
or GND.
[6] This is the increase in supply current for each input at the specified voltage level other than V
CC
or GND.
Nexperia
74LVT2245; 74LVTH2245
3.3 V octal transceiver with 30 Ω termination resistors; 3-state
74LVT_LVTH2245 All information provided in this document is subject to legal disclaimers. © Nexperia B.V. 2017. All rights reserved.
Product data sheet Rev. 5 — 10 April 2017
6 / 15
10 Dynamic characteristics
Table 7. Dynamic characteristics
Voltages are referenced to GND (ground = 0 V); for test circuit see Figure 8.
Symbol Parameter Conditions Min Typ
[1]
Max Unit
T
amb
= -40 °C to +85 °C
An to Bn or Bn to An; see Figure 6
V
CC
= 2.7 V - - 5.3 ns
t
PLH
LOW to HIGH
propagation delay
V
CC
= 3.0 V to 3.6 V 1.0 3.2 4.6 ns
An to Bn or Bn to An; see Figure 6
V
CC
= 2.7 V - - 4.9 ns
t
PHL
HIGH to LOW
propagation delay
V
CC
= 3.0 V to 3.6 V 1.0 3.1 4.5 ns
see Figure 7
V
CC
= 2.7 V - - 9.1 ns
t
PZH
OFF-state to HIGH
propagation
delay
V
CC
= 3.0 V to 3.6 V 1.1 4.5 7.0 ns
see Figure 7
V
CC
= 2.7 V - - 7.6 ns
t
PZL
OFF-state to LOW
propagation
delay
V
CC
= 3.0 V to 3.6 V 1.5 4.3 6.5 ns
see Figure 7
V
CC
= 2.7 V - - 5.6 ns
t
PHZ
HIGH to OFF-state
propagation
delay
V
CC
= 3.0 V to 3.6 V 2.2 3.7 5.2 ns
see Figure 7
V
CC
= 2.7 V - - 5.0 ns
t
PLZ
LOW to OFF-state
propagation
delay
V
CC
= 3.0 V to 3.6 V 2.0 3.6 5.0 ns
[1] Typical values are measured at V
CC
= 3.3 V and T
amb
= 25 °C.
P1-P3P4-P6P7-P9P10-P12P13-P15

74LVTH2245PW,112

Mfr. #:
Buy 74LVTH2245PW,112
Manufacturer:
Nexperia
Description:
Bus Transceivers 3.3V XCVR N-INV BH
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet