308 Constitution Drive
Menlo Park, CA 94025-1164
Phone: 800-227-4856
www.circuitprotection.com
SiBar
TM
Thyristor Surge Protectors
Raychem Circuit Protection Products
PRODUCT: TVB058SA-L
DOCUMENT: SCD 25052
PCN: 539912
REV LETTER: H
REV DATE:APRIL 28, 2007
PAGE NO.: 2 OF 2
Parameter Symbol Value Units
Repetitive Off-State Voltage, Maximum at ID = 5 µA
VDM 58 V
Non-Repetitive Peak Telcordia GR-1089 CORE 10x1000 µs
Impulse Current TIA-968 lightning Type A Metallic 10/560 µs
Double exponential TIA-968 lightning Type A Longit. 10/160 µs
Waveform Telcordia GR-1089 Intrabuilding 2/10 µs
(Notes 1 and 2) IEC61000-4-5 (Voc 1.2/50us) 8/20 µs
ITU-T K.20/K.21 (Voc 10/700us) 5/310us
TIA-968 lightning Type B (Voc 9/720us) 5/320 µs
IPP
1
IPP
2
IPP
3
IPP
4
IPP
5
IPP
6
IPP
7
50
70
90
150
150
80
80
A
A
A
A
A
A
A
Critical Rate of Rise of On-State Current
Power Pulse Amplifier, C=30μF, V=600V
Maximum 2x10 µsec waveform, V
OC
=750V, I
SC
=150A peak
di/dt
di/dt
500
100
A/µs
A/µs
DEVICE THERMAL RATINGS
Storage Temperature Range TSTG -55 to 150 ºC
Operating Temperature Range
Blocking or conducting state
TA -40 to 125 ºC
Overload Junction Temperature
Maximum; Conducting state only
TJ +150 ºC
Maximum Lead Temperature for Soldering Purpose; for 10 seconds TL +260 ºC
ELECTRICAL CHARACTERISTICS Both polarities (T
J
@ 25ºC unless otherwise noted)
Characteristics Symbol Min Typ Max Units
Breakover Voltage (+25ºC)
(dv/dt = 0.4kV/ms, I
SC
=900mA, V
DC
= 500V (both polarities))
VBO
----
64
78
V
Breakover Voltage Temperature Coefficient dVBO/dTJ ---- 0.1 ----- %/ºC
Off-State Current (VD1= 50V)
(VD2=VDM)
ID1
ID2=IDM
----
----
-----
-----
2.0
5.0
µA
µA
On-State Voltage (IT=1A)
PW ≤ 300 µsec, Duty Cycle ≤ 2% (Note 2)
VT ---- ----- 4.0 V
Breakover Current IBO ---- ----- 800 mA
Holding Current (Note 2) IH 150 ---- ---- mA
Peak Onstage Surge Current
(Measured @ 60Hz, 1 cycle, 600V)
ITSM 22 ---- ---- A
Critical Rate of Rise of Off-State Voltage
(Linear waveform, VD = 0.8 X Rated VBO, TJ= +25ºC)
dv/dt 2000 ---- ---- V/µs
Capacitance (f=1.0 Mhz, 50Vdc bias, 1Vrms)
(f=1.0 Mhz, 2Vdc bias,1Vrms)
C1
C2
----
----
43
80
----
----
pF
pF
Note 1. Allow cooling before testing second polarity
Note 2. Measured under pulse conditions to reduce heating
VOLTAGE-CURRENT CHARACTERISTIC