NOTES: (UNLESS OTHERWISE SPECIFIED)
1. ALL DIMENSIONS ARE IN INCHES [mm].
2. DIMENSIONS APPLY AFTER FINISHING.
3. MANUFACTURE TO BE COMPLIANT WITH EU RoHS DIRECTIVE.
4. SAFETY BREAK ALL SHARP CORNERS AND EDGES .02 MAXIMUM.
SHEET 1 OF 1
LDCFDLT_A
SCALE: 2:1
TITLE:
SIZE
DWG. NO.
REV
DO NOT SCALE DRAWING
ANGLES:
1
TOLERANCES:
.020 [0.50]-.200 [5.00]=
.008 [0.20]
.200 [5.00]-1.200 [30.00]=
.016 [0.40]
1.20 [30.0]-4.75 [120.0]=
.024 [0.60]
4.75 [120.0]-12.40 [315.0]=
.040 [1.0]
DRAWN:
ENGR:
DT:
DT:
MATERIAL:
FINISH:
PROJECTION:
:
THIS DRAWING CONTAINS PROPRIETARY INFORMATION
THAT IS THE SOLE PROPERTY OF LINX TECHNOLOGIES, AND SHALL BE
TREATED AS SUCH. NO DISCLOSURE OR REPRODUCTION OF THIS
DOCUMENT IS PERMITTED, IN WHOLE OR IN PART, WITHOUT THE
EXPRESS WRITTEN PERMISSION OF LINX TECHNOLOGIES OR ITS
DESIGNATED AGENTS.
159 ORT LANE
MERLIN, OR 97532
REVISIONS
REV
A
Add heat shrink, new frame, revised stripping instruct./dims 4/26/10 CJ
DESCRIPTION
DATE
APPV
Descripon Material Finish
Body
Pin
Insulaon
Nickel
N/A
Gold
PTFE
Spacer N/APTFE
O Ring RubberSi Rubber
Washer NickelBrass
Nut NickelBrass
Support NickelBrass
Heat Shrink BlackPolyolefin
Brass
BE CU
CONREVSMA014-R178
RP-SMA FEMALE BULKHEAD MOUNT CABLE
END CRIMP WITH O-RING FOR RG178 CABLE
CJ 4/26/10
0.197
(5.00)
0.032
(0.80)
RECOMMENDED CABLE STRIPPING DIMENSIONS
0.217
(5.50)
RG-178 Cable
Ø0.256
(6.50)
0.236
(6.00)
RECOMMENDED
MOUNTING HOLE
0.065
(1.65)
1/4-36UNS-2B
THREADS
H0.315
(8.00)
0.020
(0.50)
Ø0.402
(10.20)
0.433
(11.00)
FLAT 0.228
(5.80)
0.197
(5.00)
0.248
(6.30)
0.083
(2.10)
0.417
(10.60)
0.748
(19.00)
FLAT 0.228
(5.80)
Ø0.102
(2.60)
Ø0.236
(6.00)
H0.433
(11.00)
1/4"-36UNS-2A
THREADS
CONREVSMA014-R178 ASSEMBLY INSTRUCTIONS
1. Strip the cable to the recommended dimensions.
2. Slide the coax into the support until the outside insulation bottoms out
against the inside shoulder of the support.
3. Solder the support onto the braid.
4. Place the spacer onto the center conductor.
5. Solder or crimp the pin onto the center conductor.
6. Insert the pin, center conductor, spacer, and support into the body
until the top of the pin is flush to end of the body.
7. Crimp the tail of the body onto the support with a 0.093” hex crimp tool.
SPACER
SUPPORT
SIDE VIEW
BACK VIEW
WASHER
NUT
HEAT SHRINK
0.787
(20.00)
Ø0.118
(3.00)
Ø0.049
(1.24)
0.500
(12.70)
Ø0.020
(0.50)
PIN
B
B
Added new title block; update material 11-JUL-12 BPM
