NB3N853531E
http://onsemi.com
4
Table 5. CRYSTAL CHARACTERISTICS AND CONNECTIONS
Parameter Min Typ Max Unit
Mode of Oscillation Fundamental Parallel
Frequency 12 40 MHz
Equivalent Series Resistance (ESR) 50
W
Shunt Capacitance 7 pF
Drive Level 1 mW
Table 6. DC CHARACTERISTICS V
CC
= 3.3 ±5% V (3.135 to 3.465 V), V
EE
= 0 V, T
A
= −40°C to +85°C (Note 5)
Symbol Characteristic Min Typ Max Unit
I
EE
Power Supply Current 60 mA
V
IH
Input HIGH Voltage 2 V
CC
+ 0.3 V
V
IL
Input LOW Voltage −0.3 0.8 V
I
IH
Input High Current (V
CC
= 3.456 V) CLK, CLK_SEL = 3.456 V
CLK_EN = 3.456 V
150
5
mA
I
IL
Input LOW Current (V
CC
= 3.456 V) CLK, CLK_SEL = 3.456 V
CLK_EN = 3.456 V
−5
−150
mA
V
OH
Output HIGH Voltage V
CC
− 1.4 V
CC
− 0.9 V
V
OL
Output LOW Voltage V
CC
− 2.0 V
CC
− 1.7 V
VOUT
SWING
Output Voltage Swing (peak−to−peak) 0.6 1.0 V
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
5. Outputs terminated 50 W to V
CC
− 2.0 V, see Figure 4.
Table 7. AC CHARACTERISTICS V
CC
= 3.3 ±5% V (3.135 to 3.465 V), V
EE
= 0 V, TA = −40°C to +85°C (Note 6)
Symbol Characteristic Min Typ Max Unit
F
MAX
Maximum Operating Frequency 0 266 MHz
t
PD
Propagation Delay (Notes 7 and 9) 1.1 1.8 ns
tSKEW
DC
Duty Cycle Skew same path similar conditions at 50 MHz (Notes 7, 8 and 9) 46 54 %
tSKEW
O−O
Output to Output Skew Within A Device (Notes 7, 8 and 9) 30 ps
tSKEW
D−D
Device to Device Skew similar path and conditions (Notes 7, 8 and 9) 200 ps
t
JIT
Additive Phase Noise Jitter (RMS) @ 155.52 MHz (Integrated from 12 kHz to
20 MHz) See Figure 6. (Note 9)
0.053 ps
t
r
/t
f
Output rise and fall times (20% and 80% points) (Note 9) 225 600 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
6. Outputs terminated 50 W to V
CC
− 2.0 V, see Figure 4.
7. Measured under the same supply voltage, output loading, and input conditions.
8. Similar conditions.
9. Limits do not apply to overdriving XTAL_IN.