OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

3140SAR600

P1-P3P4-P6P7-P7
APEM www.apem.com
Note: The company reserves the right to change specifications without notice.
3000 series
Premium Hall effect joysticks
Distinctive features and specifications
Class leading installed depth <20 mm
Hall effect sensing
1, 2 or 3 axis
5V or 3.3V operation
EMC shielded
Analog or PWM outputs
Next generation metal mechanisms
Dual outputs available
NOTES:
1. All values are nominal.
2. All specifications shown are based on a
standard configuration and are provided
for guidance only.
3. Please refer to APEM for assistance on how
to achieve the best performance from your
chosen configuration.
4. Current consumption will be greater for
dual output configurations.
ENVIRONMENTAL
• Operating Temperature: -25ºC to 70ºC (-13ºF to 158ºF)
• Storage Temperature: -40ºC to 70ºC (-40ºF to 158ºF)
• Seal Above Panel: IP65 – Neoprene boot fitted as standard
• EMC Emission: Complies with EN 61000-6-3:2001,
CISPR 22:2005, Class B 30MHz–11GHz
• Life Cycles: 10,000,000 cycles
(5,000,000 for 3 axis joysticks)
• ESD: Complies with EN61000-4-2 (extended)
±8KV (20 contacts) & ±15KV (20 air discharges)
• EMC Immunity: 100V/m, 80MHz-2.7GHz,
1KHz 80% sine wave modulation,
EN 61000-4-3 (extended)
• Vibration: 100Hz – 200Hz @ 0.13g /Hz, total 3.6gRMS
(1 Hour in each of the three mutually perpendicular axis)
MECHANICAL
• Materials Employed: Shaft - Stainless Steel
Boot - Neoprene
Others - Brass, Nylon, ABS
• Weight: 100g (0.20lb) nominal
• Breakout Force: 1.3N (2.86lbf)
• Mechanical Angle of Movement:
36˚ for X and Y axis (subject to limiter)
50˚ for Z axis (subject to handle)
• Max Load to Mechanism: 400N (881.85lbf)
ELECTRICAL
• Gain (Output Voltage Span): ±10% x V to ±50% x V
• Output at Center: V/2 ±(5% x Gain)
• Power Supply: 5V ±0.5V Transient free
(Configs 1, 3, 4 & 5) or 3.3V ±0.1V (Config 2)
• Center Tap Impedance: 1K1
• Center Detect Output: Pulled high within joystick
via 2K2 to +V, and smoothed to 0V with 100nF
• Sensor Type: Hall effect
• Current Consumption:
5V <13mA (Two axis) <20mA (Three axis)
3.3V <24mA (Two axis) <40mA (Three axis)
• Loads: Minimum 10K, preferred 100K+
APEMwww.apem.com
Note: The company reserves the right to change specifications without notice.
3000 series
Premium Hall effect joysticks
Overview
35.80
(1.41)
35.80
(1.41)
3.20*
(0.13)
Y-
Y+
X+ X-
Z- Z+
38.50
(1.52)
42.00
(1.65)
20.00
(0.79)
62.00
(2.44)
4.50
(0.18)
CABLES EXIT TO THE EAST
WHEN VIEWED FROM ABOVE
NOTES:
1. Dimensions are in mm/(inch).
2. The dimensions shown are for generic 3000 series with E type handle. For specific dimensions of this or any other configuration please
refer to APEM.
* 3000 series has slotted mounting holes - allows compatibility with mounting pitches of 32.25mm to 35.80mm.
Configuration
1 Standard
2 3.3V Operation
3 Dual Outputs
4 Inverse Dual Outputs
5 PWM
Gain
10 ±10%xV
25 ±25%xV
30 ±30%xV
40 ±40%xV
50 ±50%xV
Handle*
BL Round
E Conical
Q Skirted
AK Push Button
AL Third Axis
* for more handles
see next pages
Limiter
A Single Axis
C Cross
D Diamond
R Round
S Square
X X Type
Modifier
00 None
20 Guided Feel
Bezel
0 None
4 Circular (below panel)
6 Square (drop-in)
7 Circular (drop-in)
SERIES
3 3000
STANDARD OPTION AVAILABILITY
The following table shows which permutations of options are possible.
CONFIGURATION CT CD AXES SUPPLY GAIN LIMITERS HANDLES BEZELS
ALL ALL
1
2
3
4
5
X Y Z 3.3V 5V 10 25 30 40 50 A C D R S X
APEM www.apem.com
Note: The company reserves the right to change specifications without notice.
3000 series
Premium Hall effect joysticks
Overview
35.80
(1.41)
35.80
(1.41)
Ø39.00
(1.54)
Ø3.20 x 4
(0.13 x 4)
NOTES: * 3000 series has slotted mounting holes - allows compatibility with mounting pitches of 32.25mm to 35.80mm.
1. Dimensions are in mm/(inch).
2. The dimensions shown are for generic 3000 series with E type handle. For specific dimensions of this or any other
configuration please refer to APEM.
3. When sub panel mounting, great care should be taken not to damage the boot, or any of the mechanism under the boot.
All panel cut-outs should be free from sharp edges and debris that may damage the boot.
DROP IN MOUNTING - PANEL CUT-OUT & MOUNTING INSTALLATION
The joystick is dropped into the panel cut-out. For panel thickness of <3mm, M3 x 16 counter-
sunk machine screws are recommended.
Please note: Image (left) shows a square bezel, a circular bezel is also available for this option.
SUB MOUNTING OPTION A - PANEL CUT-OUT & MOUNTING INSTALLATION
SUB MOUNTING OPTION B - PANEL CUT-OUT AND MOUNTING INSTALATION
When mounted this way the panel acts as the bezel and no
separate bezel is needed. M3 machine screws are recommended.
The joystick is mounted beneath the panel and the base of the boot must be brought through
the panel cut-out and held in place with the circular bezel.
For panel thickness of <3mm, M3 x 16 countersunk machine screws are recommended.
MOUNTING CUT-OUT
MOUNTING CUT-OUT
MOUNTING CUT-OUT
35.80
(1.41)
35.80
(1.41)
Ø3.20 x 4
(0.13 x 4)
35.80
(1.41)
35.80
(1.41)
Ø35.00
(1.38)
Ø3.20 x 4
(0.13 x 4)
Ø31.00
(1.22)
P1-P3P4-P6P7-P7

3140SAR600

Mfr. #:
Buy 3140SAR600
Manufacturer:
APEM
Description:
Input Devices 3000 SERIES, +/- 40% GAINSQUARE LIMITER, AR HANDLE, SQUARE DROP-IN
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet