OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

EVP-BB2A9B000

P1-P3
Light Touch Switches/EVPBB
1 2 345678
Product Code
Type Operating
Force
9
10 11 12
Note: Non washable
(
＊
1) IP67 : Switch shall not be operated during test.
Water or dust ingress shall be limited enough to prevent deleterious effect to the switch function.
However, IP67 shall be guaranteed under single product state,
then there is a possibility that IP67 performance become impaired depending on your mounting condition or usage.
So, please ask us in advance, if the switch is applied to important usage for water and dust resistant.
■ Specifications
■ Features
● External dimensions: 2.6 mm
×
1.6 mm,
Height 0.53 mm, 0.55 mm
● High operability
Equipped with an actuator (push plate)
● IP67
■ Explanation of Part Numbers
2.6 mm×1.6 mm SMD Light Touch Switches
Type:
EVPBB
■ Recommended Applications
● Operationswitchesforportableelectronicequipment
(Mobile phone, Portable audio)
Type Snap action/Push-on type SPST
Electrical
Rating 10 μA 2 V DC to 20 mA 15 V DC (Resistive load)
Contact Resistance 500 mΩ max.
Insulation Resistance 50 MΩ min. (at 100 V DC)
Dielectric Withstanding Voltage 250 V AC for 1 minute
Bouncing 10 ms max. (ON, OFF)
Mechanical
Operating Force 1.6 N, 2.4 N
Travel 0.11 mm
Endurance Operating Life 500,000 cycles min.
IP67(
＊
1)
IP6x (Dust resistance) Dust : Talc (Type4) 8 h
IPx7 (Water resistance) Immersion depth : 1m 30min.
Operating Temperature –40 °C to +85 °C
Storage Temperatur
e
–40 °C to +85 °C (Bulk)
–20 °C to +60 °C (Taping)
Minimum Quantity/Packing Unit 10,000 pcs. Embossed Taping (Reel Pack)
Quantity/Carton 50,000 pcs.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ANCTB13E 201701-Fd
 
Panasonic Corporation 2017
–1–
industrial.panasonic.com/ac/e/
201 7.01
A9B000
ANCTB13_17_22_25.indb 1 16/12/26 16:13
Light Touch Switches/EVPBB
General dimension tolerance : ± 0.05
( )dimensions are reference dimensions.
■ Dimensions in mm (not to scale)
Part Numbers Operating Force H=Height Operating Life
EVPBB2A9B000 1.6 N
0.53
mm 500,000 cycles
EVPBB4A9B000 2.4 N
0.55
mm 500,000 cycles
EVPBB
(
Embossed Taping)
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ANCTB13E 201701-Fd
 
Panasonic Corporation 2017
Panasonic Corporation
Electromechanical Control Business Division
–2–
industrial.panasonic.com/ac/e/
2-2.2
2-3.1
2-0.3
2-1.2
2-3.2
2-2.1
2-1.3
2-0.2
（2）
（1.6）
without the film and
remainder of the gate
A
A'
B
B'
B
B'
A'
Circuit diagram
A
Stencil mask plan
B
B'
A
A'
Land pattern plan
Soldering thickness t=0.08±0.01
＊Soldering failure may occur depending on applied
solder amount,so, please consider to use
our recommended stencil and land pattern desing
:Recommended land pattern area
:No soldering area
・Any land pattern or via holes shall not be
provided at area.
・If it's necessary to design land pattern or
via holes at area,
please apply resist to them to protect their
metal part completely.
・If their metal parts are not protected
completely, short circuit failure may occur
by solder ball.
・Besides, there should be convexoconcave by
designing additional pattern,
it may cause swith tilt, influence on
solder-ability or flux intrusion
after reflow soldering.
・Therefore, please study any influence of
additional land pattern or via holes at
area in advance.
（2-1.8）
（2-0.85）
2-0.75
4-0.35
0.05min.
2.6±0.1
3±0.1
（0.025）
Without the film
（0.35）
1.6±0.1
H±0.1
2-0.1max.
（φ0.91）
（φ0.7）
Actuator cross section（Section C-C）
CC
No soldering
ANCTB13_17_22_25.indb 3 16/12/26 16:13
Light Touch Switches/EVPBB
180
260
MAX.
150
230
90±30 40±10
(Normal Temp.)
Operation Top (°C)
Soldering Time (s)
Fan or Normal Temp.
Tape width=12.0 mm
Tape running direction
φ
G
D
K
C
F
A
IE
H
B
J
t
Taping condition : Lack of products in the middle of taping should be
one MAX, but total quantity specified in the
specifications should be secured.
Peeling off strength of top tape : It should be within 0.2N to 1.0N at
165 degree in peeling off angle.
Joint of carrier tape : One joint per one reel may exist.
● Embossed Carrier Taping
■ Recommended Reflow Soldering Conditions
Unit: mm
Part No.HeightABCDEFGH I JK t
EVPBB
0.53
0.55
12.0±0.3 1.75±0.10 5.5±0.1 8.0±0.1 4.0±0.1 2.0±0.1 1.5±0.3 1.95±0.20 3.3±0.2 0.7±0.2 (10.25) 0.3
+0.15
–0.10
＊
Reflow temperature may vary by location even in the same reflow condition.
Please check the reflow temperature at terminals and at the top of a switch
to make sure the both temperatures are withiin the specification.
If even one of them is out of the specifications, please adjust.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
ANCTB13E 201701-Fd
 
Panasonic Corporation 2017
Panasonic Corporation
Electromechanical Control Business Division
–3–
industrial.panasonic.com/ac/e/
ANCTB13_17_22_25.indb 2 16/12/26 16:13
P1-P3

EVP-BB2A9B000

Mfr. #:
Buy EVP-BB2A9B000
Manufacturer:
Panasonic
Description:
Tactile Switches 2.6x1.6mm 1.6N 0.11mm travel IP67
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet