5
FN6128.5
May 12, 2008
NO or NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V (Figure 7) 25 - 65 - pF
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V (Figure 7) 25 - 181 - pF
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+ V+ = +3.6V, V
IN
= 0V or V+ 25 - 0.01 - µA
Full - 0.52 - µA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
25 - - 0.5 V
Input Voltage High, V
INH
25 1.4 - - V
Input Current, I
INH
, I
INL
V+ = 3.3V, V
IN
= 0V or V+ (Note 9) Full -0.5 - 0.5 µA
Electrical Specifications - 1.8V Supply Test Conditions: V+ = +1.65V to +2V, GND = 0V, VINH = 1.0V, VINL = 0.4V (Note 6),
Unless otherwise specified.
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 7, 11) TYP
MAX
(Notes 7, 11) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 - V+ V
ON-Resistance, r
ON
V+ = 1.65V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+
(Figure 5)
25 - 0.7 0.8 Ω
Full - - 0.85 Ω
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 1.65V, V
NO
or V
NC
= 1.0V, R
L
= 50Ω, C
L
= 35pF
(Figure 1)
25 - 70 - ns
Full - 80 - ns
Turn-OFF Time, t
OFF
V+ = 1.65V, V
NO
or V
NC
= 1.0V, R
L
= 50Ω, C
L
= 35pF
(Figure 1)
25 - 54 - ns
Full - 65 - ns
Break-Before-Make Time Delay, t
D
V+ = 2.0V, V
NO
or V
NC
= 1.0V, R
L
= 50Ω, C
L
= 35pF
(Figure 3)
Full - 10 - ns
Charge Injection, Q C
L
= 1.0nF, V
G
= 0V, R
G
= 0Ω (Figure 2) 25 - 42 - pC
NO or NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V (Figure 7) 25 - 70 - pF
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V (Figure 7) 25 - 186 - pF
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
25 - - 0.4 V
Input Voltage High, V
INH
25 1.0 - - V
Input Current, I
INH
, I
INL
V+ = 2.0V, V
IN
= 0V or V+ (Note 9) Full -0.5 - 0.5 µA
NOTES:
6. V
IN
= input voltage to perform proper function.
7. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
8. Flatness is defined as the difference between maximum and minimum value of ON-resistance over the specified analog signal range.
9. Limits established by characterization and are not production tested.
10. R
ON
matching between channels is calculated by subtracting the channel with the highest max r
ON
value from the channel with lowest max r
ON
value, between NC1 and NC2 or between NO1 and NO2.
11. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V
INH
= 1.4V, V
INL
= 0.5V (Note 6),
Unless otherwise specified. (Continued)
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 7, 11) TYP
MAX
(Notes 7, 11) UNITS
ISL8484
