ADuM7440/ADuM7441/ADuM7442 Data Sheet
Rev. D | Page 14 of 20
APPLICATIONS INFORMATION
PRINTED CIRCUIT BOARD (PCB) LAYOUT
The ADuM7440/ADuM7441/ADuM7442 digital isolators
require no external interface circuitry for the logic interfaces.
Power supply bypassing is strongly recommended at the input
and output supply pins (see Figure 16). A total of four bypass
capacitors should be connected between Pin 1 and Pin 2 for
V
DD1A
, between Pin 7 and Pin 8 for V
DD1B
, between Pin 9 and
Pin 10 for V
DD2B
, and between Pin 15 and Pin 16 for V
DD2A
.
Supply V
DD1A
Pin 1 and V
DD1B
Pin 7 should be connected
together and supply V
DD2B
Pin 10 and V
DD2A
Pin 16 should be
connected together. The capacitor values should be between
0.01 μF and 0.1 μF. The total lead length between both ends of
the capacitor and the power supply pin should not exceed 20 mm.
V
DD1A
GND
1
V
IA
V
IB
IC/
V
OC
ID/
V
OD
V
DD1B
GND
1
V
DD2A
GND
2
V
OA
V
OB
V
OC/
V
IC
V
OD/
V
ID
V
DD2B
GND
2
08340-014
Figure 16. Recommended Printed Circuit Board Layout
In applications involving high common-mode transients, it is
important to minimize board coupling across the isolation barrier.
Furthermore, users should design the board layout so that any
coupling that does occur equally affects all pins on a given
component side. Failure to ensure this can cause voltage differentials
between pins exceeding the absolute maximum ratings of the
device, thereby leading to latch-up or permanent damage.
See the AN-1109 Application Note for board layout guidelines.
PROPAGATION DELAY-RELATED PARAMETERS
Propagation delay is a parameter that describes the time it takes
a logic signal to propagate through a component. The input-to-
output propagation delay time for a high-to-low transition may
differ from the propagation delay time of a low-to-high transition.
INPUT (V
Ix
)
OUTPUT (V
Ox
)
t
PLH
t
PHL
50%
50%
08340-008
Figure 17. Propagation Delay Parameters
Pulse width distortion is the maximum difference between
these two propagation delay values and an indication of how
accurately the timing of the input signal is preserved.
Channel-to-channel matching refers to the maximum amount
the propagation delay differs between channels within a single
ADuM7440/ADuM7441/ADuM7442 component.
Propagation delay skew refers to the maximum amount the
propagation delay differs between multiple ADuM7440/
ADuM7441/ADuM7442 components operating under the
same conditions.
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY
Positive and negative logic transitions at the isolator input cause
narrow (~1 ns) pulses to be sent to the decoder using the
transformer. The decoder is bistable and is, therefore, either set
or reset by the pulses, indicating input logic transitions. In the
absence of logic transitions at the input for more than ~1 μs, a
periodic set of refresh pulses indicative of the correct input state
is sent to ensure dc correctness at the output. If the decoder
receives no internal pulses of more than approximately 5 μs, the
input side is assumed to be unpowered or nonfunctional, in which
case the isolator output is forced to a default high state by the
watchdog timer circuit.
The magnetic field immunity of the ADuM7440/ADuM7441/
ADuM7442 is determined by the changing magnetic field,
which induces a voltage in the transformer’s receiving coil large
enough to either falsely set or reset the decoder. The following
analysis defines the conditions under which this can occur. The
3 V operating condition of the ADuM7440/ADuM7441/
ADuM7442 is examined because it represents the most
susceptible mode of operation.
The pulses at the transformer output have an amplitude greater
than 1.0 V. The decoder has a sensing threshold at about 0.5 V, thus
establishing a 0.5 V margin in which induced voltages can be
tolerated. The voltage induced across the receiving coil is given by
V = (−dβ / dt) ∑ π r
n
2
; n = 1, 2, … , N
where:
β is magnetic flux density (gauss).
r
n
is the radius of the n
th
turn in the receiving coil (cm).
N is the number of turns in the receiving coil.
Given the geometry of the receiving coil in the ADuM7440/
ADuM7441/ADuM7442 and an imposed requirement that the
induced voltage be, at most, 50% of the 0.5 V margin at the
decoder, a maximum allowable magnetic field at a given
frequency can be calculated. The result is shown in Figure 18.