Philips Semiconductors Product data sheet
74ALVT165432.5 V/3.3 V 16-bit registered transceiver (3-State)
2004 Sep 14
6
DC ELECTRICAL CHARACTERISTICS (3.3 V ± 0.3 V RANGE)
LIMITS
SYMBOL PARAMETER TEST CONDITIONS Temp = –40 °C to +85 °C UNIT
MIN TYP
1
MAX
V
IK
Input clamp voltage V
CC
= 3.0 V; I
IK
= –18 mA – –0.85 –1.2 V
p
V
CC
= 3.0 V to 3.6 V; I
OH
= –100 µA V
CC
– 0.2 V
CC
–
OH
-
V
CC
= 3.0 V; I
OH
= –32 mA 2.0 2.3 –
V
CC
= 3.0 V; I
OL
= 100 µA – 0.07 0.2
p
V
CC
= 3.0 V; I
OL
= 16 mA – 0.25 0.4
OL
–
V
CC
= 3.0 V; I
OL
= 32 mA – 0.3 0.5
V
CC
= 3.0 V; I
OL
= 64 mA – 0.4 0.55
V
RST
Power-up output low voltage
6
V
CC
= 3.6 V; I
O
= 1 mA; V
I
= V
CC
or GND – – 0.55 V
V
CC
= 3.6 V; V
I
= V
CC
or GND Control pins – 0.1 ± 1
V
CC
= 0 V or 3.6 V; V
I
= 5.5 V – 0.1 10
I
I
Input leakage current V
CC
= 3.6 V; V
I
= V
CC
– 0.5 1 µA
V
CC
= 3.6 V; V
I
= 0 V Data pins
– 0.1 –5
V
CC
= 3.6 V; V
I
= 5.5 V – 0.1 20
I
OFF
Off current V
CC
= 0 V; V
I
or V
O
= 0 V to 4.5 V – 0.1 ± 100 µA
V
CC
= 3 V; V
I
= 0.8 V 75 130 –
I
HOLD
us
o
curren
p
7
V
CC
= 3 V; V
I
= 2.0 V –75 –140 – µA
V
CC
= 0 V to 3.6 V; V
CC
= 3.6 V ± 500 – –
I
EX
Current into an output in the
High state when V
O
> V
CC
V
O
= 5.5 V; V
CC
= 3.0 V – 50 125 µA
I
PU/PD
Power-up/down 3-State output
current
3
V
CC
≤ 1.2 V; V
O
= 0.5 V to V
CC
; V
I
= GND or V
CC
;
OE/OE = Don’t care
– 40 ± 100 µA
I
CCH
V
CC
= 3.6 V; Outputs HIGH; V
I
= GND or V
CC
;
I
O
= 0 mA
– 0.07 0.1
I
CCL
Quiescent supply current
V
CC
= 3.6 V; Outputs LOW; V
I
= GND or V
CC
;
I
O
= 0 mA
– 3.6 5
mA
I
CCZ
V
CC
= 3.6 V; Outputs disabled;
V
I
= GND or V
CC,
I
O
=
0 mA
5
– 0.07 0.1
∆I
CC
Additional supply current per
input pin
2
V
CC
= 3 V to 3.6 V; One input at V
CC
– 0.6 V;
Other inputs at V
CC
or GND
– 0.04 0.4 mA
NOTES:
1. All typical values are at V
CC
= 3.3 V and T
amb
= 25 °C.
2. This is the increase in supply current for each input at the specified voltage level other than V
CC
or GND.
3. This parameter is valid for any V
CC
between 0 V and 1.2 V with a transition time of up to 10 msec. From V
CC
= 1.2 V to V
CC
= 3.3 V ± 0.3 V
a transition time of 100 µsec is permitted. This parameter is valid for T
amb
= 25 °C only.
4. Unused pins at V
CC
or GND.
5. I
CCZ
is measured with outputs pulled up to V
CC
or pulled down to ground.
6. For valid test results, data must not be loaded into the flip-flops (or latches) after applying power.
7. This is the bus hold overdrive current required to force the input to the opposite logic state.
