2001-2012 Microchip Technology Inc. DS21402D-page 1
TC32M
Features:
Incorporates the Functionality of the Industry
Standard TC1232 (Processor Monitor, Watchdog
and Manual Override Reset Controller) into a
Small, Lower Cost Package
Guards Against Unstable Processor Operation
Resulting from Power “Brown-Out
Automatically Halts and Restarts an Out-of-
Control Microprocessor
Output can be Wire-ORed, or Hooked to Manual
Reset Push-button Switch
Space-Saving 3-Pin TO-92 or SOT-223 Package
Applications:
All Microprocessor-Based Systems
Battery Powered Computers and Controllers
Automotive Systems
Intelligent Instruments
Critical Processor Monitoring
Embedded Controllers
Device Selection Table
Package Type
General Description:
The TC32M is a fully-integrated processor supervisor
in a 3-pin package. It provides three important func-
tions to safeguard processor sanity: precision power
on/off Reset control, Watchdog Timer and external
Reset override.
On power-up, the TC32M holds the processor in the
Reset state for a minimum of 500 msec after V
DD
is
within tolerance to ensure a stable system start-up.
Microprocessor sanity is monitored by the on-board
Watchdog circuit. The microprocessor must provide a
high-to-low level shift (through an external resistor
divider) on the RS pin of the TC32M. Should the
processor fail to supply this signal within the specified
time-out period (typically 700 msec), an out-of-control
processor is indicated and the TC32M issues a
processor Reset as a result.
The output of the TC32M can be wire-ORed with a
push-button switch (or electronic signal) to override the
TC32M and unconditionally reset the processor. When
connected to a push-button switch, the TC32M
provides contact debounce.
The TC32M is packaged in a space-saving TO-92 or
SOT-223 package. It provides all of the functionality of
the industry standard TC1232 in a smaller, lower cost
configuration.
Part Number Package Temp. Range
TC32MCDB SOT-223 0°C to +70°C
TC32MCZB TO-92 0°C to +70°C
TC32MEDB SOT-223 -40°C to +85°C
TC32MEZB TO-92 -40°C to +85°C
1
12
4
3
23
GND
GND
TC32MCDB
TC32MEDB
TC32MCZB
TC32MEZB
V
DD
V
DD
V
DD
RS
RS
ECONOMONITOR™ – 3-Pin System Supervisor with
Power Supply Monitor and Watchdog
TC32M
DS21402D-page 2 2001-2012 Microchip Technology Inc.
Functional Block Diagram Typical Operating Circuit
V
DD
V
REF2
V
REF1
TC32M
Watchdog
Timer
RS
GND
DV
Detector
Delay
Timer
5V
R1, 10 kΩ
R2, 10 kΩ
RS
TC32M
Microcontroller
Reset
PO.1
Reset
2001-2012 Microchip Technology Inc. DS21402D-page 3
TC32M
1.0 ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings*
Supply Voltage (V
DD
to GND) .............................+6.0V
Input Voltage Any Pin.....(GND – 0.3V) to (V
DD
+0.3V)
Operating Temperature Range
TC32MC Package........................... 0°C to +70°C
TC32ME Package........................-40°C to +85°C
Storage Temperature Range .............-65°C to +150°C
*Stresses above those listed under “Absolute Maxi-
mum Ratings” may cause permanent damage to the
device. These are stress ratings only and functional
operation of the device at these or any other conditions
above those indicated in the operation sections of the
specifications is not implied. Exposure to Absolute
Maximum Rating conditions for extended periods may
affect device reliability.
TC32M ELECTRICAL SPECIFICATIONS
Recommended DC Operating Conditions: T
A
= -40°C to +85°C unless otherwise noted.
Symbol Parameter Min Typ Max Units Test Conditions
V
DD
Supply Voltage 4.5 5.5 V
V
IH
RS Input HIGH Level for PB 2.0 V
V
IL
RS Input LOW Level for PB 0.3 V
DC Electrical Characteristics: V
DD
= 4.5V to 5.5V, T
A
= -40°C to +85°C unless otherwise noted.
Symbol Parameter Min Typ Max Units Test Conditions
I
IL
RS Input Leakage -1 +1 mA
I
OL
RS Output Current 2.0 10 mA V
OL
= 0.4V
I
CC
Operating Current 50 200 A Note 1
V
STH
RS Strobe HIGH Level (V
DD
– 0.5V) V Figure 3-1
V
STL
RS Strobe LOW Level 2.00 (V
DD
– 1.5V) V Figure 3-1
V
RST
Reset Threshold 4.25 4.50 V V
DD
Falling (Note 2, Figure 3-3)
Capacitance Electrical Characteristics: T
A
= 25°C unless otherwise noted.
Symbol Parameter Min Typ Max Units Test Conditions
C
IN
Input Capacitance 5 pF
C
OUT
Output Capacitance 7 pF
AC Electrical Characteristics: T
A
= -40°C to +85°C, V
DD
= 5V ±10%, unless otherwise noted.
Symbol Parameter Min Typ Max Units Test Conditions
t
RST
Reset Active Time 500 700 900 msec Figure
t
ST
RS Strobe Pulse Width 500 nsec Figure 3-1
t
TD
Watchdog Time-out Period 500 700 900 msec Figure 3-1
t
RPD
V
DD
Detect to RS LOW nsec Figure 3-1
Note 1: No output load.
2: All voltages referenced to ground.

TC32MEDB713

Mfr. #:
Manufacturer:
Microchip Technology
Description:
Supervisory Circuits Economonitor
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet