DO NOT
SCALE FROM
THIS PRINT
.203 5.16
.2450
±.0030
6.223
±0.076
.012
REF
0.30
.03937
(TO BE MEASURED AT THE TAIL TIP)
1.0000
2
MAX SWAY
(TYP)
"B"
"B"
WT-10-01-XX
FC1-XX-S
-02 / -L2 [HORIZONTAL LEAD STYLES]
01
(No OF POS x .03937[1.0000])
+ .092 [2.34] REF
(No OF POS x .03937[1.0000])
+ .03937[1.0000] REF
.109
REF
2.77
{(NO OF POS - 1 ) x
.03937 [1.0000]}
.002 [.05]
C
-01 / -L1 [VERTICAL LEAD STYLES]
01
02
03
FC1-XX-XX-XX-XX
No OF POSITIONS
-05 THRU -25
(SEE NOTE 8 )
LEAD STYLE
-01 VERTICAL (SEE FIG 2, C-136-01-X)
-02 HORIZONTAL (SEE FIG. 1) (C-136-02-X)
-L1 VERTICAL (LOW INSERTION FORCE) (C-136-03-X)
-L2 HORIZONTAL (LOW INSERTION FORCE) (C-136-04-X)
PLATING
OPTIONS
-WT: WELD TAB (LEAD
STYLE -02 & -L2 ONLY)
-LC: LOCKING CLIP (SEE FIG 3)
(LEAD STYLE -01 & -L1 ONLY)
(SEE NOTE 9)
-K: POLYIMIDE FILM PAD
(LEAD STYLE -01 & -L1 ONLY)
(USE K-DOT-.157-.250-.005)
(SEE NOTE 7)
-TR: TAPE & REEL
-T: MATTE TIN CONTACT AND TAIL
-TM: MATTE TIN CONTACT AND TAIL
.026 0.67
.065
REF
1.638
.204
±.003
5.182
±0.08
C-136-01-XX
OR
C-136-03-XX
C
FIG 2
-01 /-L1: VERTICAL
DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1
C
.004[.10]
.033
REF
0.84
.132 3.35
REF
.060
REF
1.524
"A" REF
'A'
SECTION "B"-"B"
-LC OPTION
C-136-02-XX
OR
C-136-04-XX
FIG 3
SAME AS FIG. 2 EXCEPT AS SHOWN
C
.004 [0.10]
.010
REF
0.25
{(NO OF POS x .03937 [1.0000])
+ .059 [1.50]}
.005 [.13]
LC-06-TM
.056
REF
1.42
.055
-
.000
+
.010
1.40
0.00
+
0.25
.001 0.03
DETAIL 'A'
SCALE 8 : 1
C
RECOMMENDED CABLE WIDTH
{(NO. OF POSITIONS x .03937 [1.0000])
+ .040 [1.00] +/- .010 [.25] }
(SEE NOTE 6)
FIG 1
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 [.3] 2
.XXX:
.005 [.13]
.XXXX:
.0020 [.508]
BY:
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
G. PURVIS
3/1/1999
2
1
SHEET SCALE: 4:1
F:\DWG\MISC\MKTG\FC1-XX-XX-XX-XX-MKT.SLDDRW
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. NOTE DELETED
3. BURR ALLOWANCE: .0015[.038] MAX.
4. MAXIMUM CUT FLASH: .010 [.25].
5. MINIMUM PUSHOUT FORCE: .5 LB.
6. TAIL SWAY MUST BE IN SAME DIRECTION
ON ALL CONTACT TAILS.
7. KAPTON PAD (-K) AVAILABLE ON ALL POSITIONS FOR LEAD STYLE
-01 & -L1 (SEE FIG. 4).
8. -05 THRU -10 POSITIONS ARE 2 PARTS PER AND REQUIRE MULTI-CUTTING.
9. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE –LC OPTION IS NOT
COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS MANUAL
PLACEMENT FOR ALL ASSEMBLIES WITH THE –LC OPTION.
HOUSING: BLACK LCP
CONTACT: PHOSPHOR BRONZE
WELD TABS: BRASS
1MM SOCKET
FC1-XX-XX-XX-XX
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
REVISION AC
