OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

SG7805AK

P1-P3P4-P6P7-P8
SG78xxA/78xx
PRODUCT DATASHEET
Microsemi
Analog Mixed Signal Group
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 1
WWW.Microsemi .COM
Copyright © 1997
Rev. 1.5, 2010-07-13
TM
®
Positive Fixed Voltage Regulator
DESCRIPTION
The SG78xxA/SG78xx series of
positive regulators offer self contained,
fixed-voltage capability with up to 1.5A of
load current and input voltage up to 50V
(SG78xxA series only). These units
feature a unique on-chip trimming system
to set the output voltages to within ±1.5%
of nominal on the SG78xxA series, ±2.0%
on the SG78xx series. The SG78xxA
versions also offer much improved line
and load regulation characteristics.
Utilizing an improved bandgap reference
design, problems have been eliminated
that are normally associated with the Zener
diode references, such as drift in output
voltage and large changes in the line and
load regulation.
All protective features of thermal
shutdown, current limiting, and safe-area
control have been designed into these units
and since these regulators require only a
small output capacitor for satisfactory
performance, ease of application is assured.
Although designed as fixed-voltage
regulators, the output voltage can be
increased through the use of a simple
voltage divider. The low quiescent drain
current of the device insures good regulation
when this method is used. Product is
available in hermetically sealed TO-257
(both case grounded ‘G’ and isolated ‘IG’),
TO-3, TO-39 and LCC packages.
IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com
KEY FEATURES
Output Voltage Set Internally to
±1.5% on SG78xxA
Input Voltage Range to 50V max.
on SG78xxA
Two Volt Input-Output Differential
Excellent Line and Load Regulation
Foldback Current Limiting
Thermal Overload Protection
Voltages Available: 5V, 12V, 15V
Contact Factory for Other Voltage
Options
Available in Surface Mount
Package
HIGH RELIABILITY FEATURES
- SG78xxA/78xx
Available to MIL-STD – 883, ¶ 1.2.1
MIL-M38510/10702BXA - JAN7805T
MIL-M38510/10703BXA - JAN7812T
MIL-M38510/10704BXA - JAN7815T
MIL-M38510/10706BYA - JAN7805K
MIL-M38510/10707BYA - JAN7812K
MIL-M38510/10708BYA - JAN7815K
Radiation Data Available
MSC-AMSG level "S" Processing Available
Available to DSCC
– Standard Microcircuit Drawing (SMD)
PRODUCT HIGHLIGHT
SCHEMATIC DIAGRAM
*
* For normal operation the (V
OS
) sense pin must be externally connected to the load.
S
S
G
G
7
7
8
8
X
X
X
X
SG78xxA/78xx
PRODUCT DATASHEET
Microsemi
Analog Mixed Signal Group
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 2
WWW.Microsemi .COM
Copyright © 1997
Rev. 1.5, 2010-07-13
TM
®
Positive Fixed Voltage Regulator
ABSOLUTE MAXIMUM RATINGS
Device Output Voltage Input Voltage
Input Voltage
(Transient)(Note 3)
Input Voltage Differential
(Output Shorted to Ground)
5V 35V 50V 35V
12V 35V 50V 35V
15V 35V 50V 35V
Operating Junction Temperature ......................................................................................................................................................... 150°C
Storage Temperature Range ................................................................................................................................................. -65°C to 150°C
Lead Temperature (Soldering 10 seconds) .......................................................................................................................................... 300°C
Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of
specified terminal
.
Note 3: Operation at high input voltages is dependent upon load current. When load current is less than 5mA, output will rise out of regulation as input-
output differential increases beyond 30V. Note also from figure 1, that maximum load current is reduced at high voltages. The 50V input rating of the
SG78xxA series refers to ability to withstand high line or transient conditions without damage. Since the regulator’s maximum current capability is
reduced, the output may fall out of regulation at high input voltages under nominal loading.
THERMAL DATA
K
TO-3 3-Terminal Metal Can (Two pins and case)
THERMAL RESISTANCE-JUNCTION TO CASE, θ
JC
3.0°C/W
THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ
J
A
35°C/W
T
TO-39 3-Pin Metal Can
THERMAL RESISTANCE-JUNCTION TO CASE, θ
JC
15°C/W
THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ
J
A
120°C/W
G
TO-257 3-Pin Hermetic
THERMAL RESISTANCE-JUNCTION TO CASE, θ
JC
3.5°C/W
THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ
J
A
42°C/W
IG
TO-257 3-Pin Hermetic (Isolated)
THERMAL RESISTANCE-JUNCTION TO CASE, θ
JC
4.0°C/W
THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ
J
A
42°C/W
L
Leadless Chip Carrier 20-Pin Ceramic
THERMAL RESISTANCE-JUNCTION TO CASE, θ
JC
35°C/W
THERMAL RESISTANCE-JUNCTION TO AMBIENT, θ
J
A
120°C/W
Junction Temperature Calculation: T
J
= T
A
+ (P
D
x θ
JA
).
The θ
J
A
numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow.
P
P
A
A
C
C
K
K
A
A
G
G
E
E
D
D
A
A
T
T
A
A
SG78xxA/78xx
PRODUCT DATASHEET
Microsemi
Analog Mixed Signal Group
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 3
WWW.Microsemi .COM
Copyright © 1997
Rev. 1.5, 2010-07-13
TM
®
Positive Fixed Voltage Regulator
CHARACTERISTIC CURVES
Figure 1 – Peak Output Current vs.
Input – Output Differential
Figure 2 – Minimum Input – Output Voltage vs.
Load Current
Figure 3 – Ripple Rejection vs. Frequency
Figure 4 – Temperature Coefficient of Output Voltage
G
G
R
R
A
A
P
P
H
H
S
S
P1-P3P4-P6P7-P8

SG7805AK

Mfr. #:
Buy SG7805AK
Manufacturer:
Microchip / Microsemi
Description:
IC REG LINEAR 5V 1.5A TO204AD
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet