2 of 47 October 3, 2011
IDT 89HPES48T12 Data Sheet
– Internal end-to-end parity protection on all TLPs ensures data
integrity even in systems that do not implement end-to-end
CRC (ECRC)
– Supports optional PCI Express Advanced Error Reporting
– Supports PCI Express Hot-Plug
• Compatible with Hot-Plug I/O expanders used on PC
motherboards
– Supports Hot-Swap
◆
Power Management
– Supports PCI Power Management Interface specification,
Revision 1.1 (PCI-PM)
• Supports powerdown modes at the link level (L0, L0s, L1,
L2/L3 Ready and L3) and at the device level (D0, D3
hot
)
– Unused SerDes disabled
◆
Testability and Debug Features
– Built in SerDes Pseudo-Random Bit Stream (PRBS) generator
– Ability to read and write any internal register via the SMBus
– Ability to bypass link training and force any link into any mode
– Provides statistics and performance counters
◆
32 General Purpose Input/Output pins
– Each pin may be individually configured as an input or output
– Each pin may be individually configured as an interrupt input
– Some pins have selectable alternate functions
◆
Packaged in a 35mm x 35mm 1156-ball Flip Chip BGA with
1mm ball spacing
Product Description
Utilizing standard PCI Express interconnect, the PES48T12 provides
the most efficient connectivity solution for applications requiring high
throughput, low latency, and simple board layout with a minimum
number of board layers. It provides 192 Gbps of aggregated switching
capacity through 48 integrated serial lanes, using proven and robust IDT
technology. Each lane provides 2.5 Gbps of bandwidth in both directions
and is fully compliant with PCI Express Base specification 1.1.
The PES48T12 is based on a flexible and efficient layered architec-
ture. The PCI Express layers consist of SerDes, Physical, Data Link and
Transaction layers. The PES48T12 can operate either as a store and
forward switch or a cut-through switch and is designed to switch memory
and I/O transactions. It supports eight Traffic Classes (TCs) and one
Virtual Channel (VC) with sophisticated resource management to enable
efficient switching and I/O connectivity.
SMBus Interface
The PES48T12 contains two SMBus interfaces. The slave interface
provides full access to the configuration registers in the PES48T12,
allowing every configuration register in the device to be read or written
by an external agent. The master interface allows the default configura-
tion register values of the PES48T12 to be overridden following a reset
with values programmed in an external serial EEPROM. The master
interface is also used by an external Hot-Plug I/O expander.
Six pins make up each of the two SMBus interfaces. These pins
consist of an SMBus clock pin, an SMBus data pin, and 4 SMBus
address pins. In the slave interface, these address pins allow the SMBus
address to which the device responds to be configured. In the master
interface, these address pins allow the SMBus address of the serial
configuration EEPROM from which data is loaded to be configured. The
SMBus address is set up on negation of PERSTN by sampling the
corresponding address pins. When the pins are sampled, the resulting
address is assigned as shown in Table 1.
Figure 2 Port Configuration Examples
Note: The configurations in the above diagram show the maximum port widths. The PES48T12 can negotiate to narrower port widths — x4,
x2, or x1.
0
2
3
54 6 7 8 9
10
11
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x8
x8
x8
x8
x8
x8
1 0
11
10
4 5
8 9
6 7
2
3
Non-bifurcated
Fully Bifurcated
1
x4