BA7613F-E2

4
Multimedia ICs BA7613N / BA7613F
Measurement conditions
SW1 SW2 SW3 SW4 SW5
ICC 22222
I
N1
IN2
IN3
Vom
Vom
Vom
1
2
2
2
1
2
2
2
1
3
3
2
3
2
3
I
N1
IN2
IN3
GV
GV
GV
1
2
2
2
1
2
2
2
1
3
3
2
3
2
3
I
N1IN2
IN1IN3
IN1MUTE
I
N2IN3
IN2MUTE
I
N3MUTE
C
T
CT
CT
CT
CT
CT
1
1
1
2
2
2
2
2
2
1
1
2
2
2
2
2
2
1
3
2
2
2
2
2
2
3
2
3
2
2
I
N1
IN2
IN3
Gf
Gf
Gf
1
2
2
2
1
2
2
2
1
3
3
2
3
2
3
CTLA
CTLB
V
TH
VTH
2
2
2
1
1
2
1
3
3
1
f = 1kHz
THD = 0.5%
f = 1MHz,
V = 1V
P-P
f = 4.43MHz,
V = 1VP-P
V
=
1V
P-P
f
=
10MHz / f
=
1MHz,
1
2
3
4
5
Parameter Symbol
Switch settings
Measurement
method
Current dissipation
Ammeter
Maximum
output
level
Voltage gain
Interchannel
crosstalk
Frequency
characteristic
CTL pin
switching level
1: Connect a distortion meter to the output, and input a f = 1kHz sine wave. Adjust the input level until the output distortion is 0.5%. This
output voltage at this time multiplied by 2 is the maximum output level V
om (VP-P).
2: Input a 1VP-P, 1MHz sine wave. The voltage gain is given by GV = 20 log (VOUT / VIN) + 6.
3: Input a 1VP-P, 4.43MHz sine wave. The interchannel crosstalk is given by CT = 20 log (VOUT / VIN).
4: Input 1VP-P, 1MHz and 10MHz sine waves.
The frequency characteristic is given by G
f = 20 log (VOUT (f = 10MHz) / VOUT (f = 1MHz)).
5: Input a 1VP-P, 1MHz sine wave. Reduce the CTL pin voltage from VCC.
The CTL pin switching level (V
TH) is the CTL pin voltage at which the VOUT level drops below 20mVP-P.
Electrical characteristic curves
5
4
3
2
1
0
01234
5
OUTPUT VOLTAGE: VOUT (VP-P)
INPUT VOLTAGE: VIN (VP-P)
VCC
=
12V
VCC = 9V
VCC = 5V
Fig. 2 VIN vs. VOUT (f = 1kHz)
4
100k 300k 1M 3M 10M 30M 100M
2
2
0
4
VOLTAGE GAIN: Cf (dB)
FREQUENCY: f (Hz)
Fig. 3 Frequency characteristics
80
100k 300k 1M 3M 10M 30M 100M
60
40
20
0
20
CROSSTALK: CT (dB)
FREQUENCY: f (Hz)
Fig. 4 Interchannel crosstalk
Operation notes
The output impedance is approximately 32. Therefore,
to ensure output matching, connect an external resistor of 43.
5
Multimedia ICs BA7613N / BA7613F
External dimensions (Units: mm)
SIP8 SOP8
BA7613N BA7613F
10.5 ± 0.5
1
8
2.54
3.5 ± 0.5
1.3
0.8
0.6
0.3 ± 0.1
2.8 ± 0.2
19.3 ± 0.2
1.2
5.8 ± 0.2
0.4 ± 0.11.27
0.15
0.3Min.
0.15 ± 0.1
0.11
6.2 ± 0.3
4.4 ± 0.2
5.0 ± 0.2
85
41
1.5 ± 0.1
Appendix
Appendix1-Rev1.0
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document use silicon as a basic material.
Products listed in this document are no antiradiation design.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.

BA7613F-E2

Mfr. #:
Manufacturer:
Description:
Video ICs AV SWITCH
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet