OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

EVAL-ADUC7060QSPZ

P1-P3P4-P6P7-P9P10-P12
Evaluation Board User Guide
UG-029
One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Te l: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
ADuC7060 Evaluation Board User Guide
MicroConverter® ADuC7060 Development System
See the last page for an important warning and disclaimers. Rev. 0 | Page 1 of 12
FEATURES
2-layer PCB (4 in. × 5 in. form factor)
9 V power supply regulated to 3.3 V and 2.5 V on board
4-pin UART header to connect to RS-232 interface cable
20-pin standard JTAG connector
Demonstration circuit
32.768 kHz watch crystal to drive the PLL clock
ADR280 1.2 V external reference chip
Reset/download/IRQ0 push buttons
Power indicator/general-purpose LEDs
Access to all ADC inputs and DAC output from external header;
all device ports are brought out to external header pins
Surface-mount and through-hole general-purpose
prototype area
EVALUATION KIT CONTENTS
mIDAS-Link JTAG programming POD
CD containing evaluation software including user manuals,
data sheets, example code, ARMWSD, and evaluation
compilers
9 V power supply
RS-232 to UART cable
USB cable
GENERAL DESCRIPTION
This user guide refers to the ADuC7060 evaluation board.
This evaluation board allows evaluation of the ADuC7060
and ADuC7061 parts. The ADuC7060 is the superset of the
ADuC706x series, and all features of the ADuC7061 can be
evaluated using the ADuC7060. The ADuC7060 contains an
ARM7TDMI core, 32 kB of flash, 4 kB of SRAM, dual 24-bit
sigma-delta (Σ-Δ) ADCs, and a 12-bit DAC as well as many
other features.
This evaluation board allows a user to program the ADuC7060
via the JTAG or the UART interfaces. The user may also debug
their source code through the JTAG interface.
In this user guide, all references to the physical orientation
of components on the board are made with respect to a
component-side view of the board with the prototype area
appearing in the bottom of the board.
The board is laid out to minimize coupling between the analog
and digital sections of the board. To this end, the ground plane
is split with the analog section on the left side and a digital
plane on the right side of the board. The regulated 2.5 V power
supply is routed directly to the digital section and is filtered
before being routed into the analog section of the board.
UG-029 Evaluation Board User Guide
Rev. 0 | Page 2 of 12
TABLE OF CONTENTS
Features .............................................................................................. 1
Evaluation Kit Contents ................................................................... 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Evaluation Board Hardware ............................................................ 3
Power Supply ................................................................................. 3
RS-232 Interface ........................................................................... 3
Emulation Interface ...................................................................... 3
Crystal Circuit ............................................................................... 3
External Reference (ADR280) .................................................... 3
Reset/Download/IRQ0 Push Buttons ........................................ 3
Power Indicator/General Purpose LEDs ................................... 4
Analog I/O Connections ............................................................. 4
General-Purpose Prototype Area ................................................4
DIP Switch Link Options .................................................................5
External Connectors .........................................................................6
Analog I/O Connector J2 .............................................................6
Power Supply Connector J1 .........................................................6
Emulation Connector J5 ...............................................................6
Serial Interface Connector J4 .......................................................6
Digital I/O Connector J3 ..............................................................6
RTD Demonstration Circuit ............................................................7
Evaluation Board Schematic and Artwork .....................................8
Bill of Materials ............................................................................... 11
ESD Caution................................................................................ 11
REVISION HISTORY
8/09—Revision 0: Initial Version
Evaluation Board User Guide UG-029
Rev. 0 | Page 3 of 12
EVALUATION BOARD HARDWARE
POWER SUPPLY
Connect the 9 V power supply via the 2 mm input power socket
(J1). The input connector is configured as a center negative, that
is, with GND on the center pin and 9 V on the outer shield.
The 9 V supply is regulated via the linear voltage regulator, U3.
The 2.5 V regulator output is used to drive the digital side of the
board directly. The 2.5 V supply is also filtered and then used to
supply the analog side of the board. This regulator supplies the
ADuC7060 microcontroller.
The 9 V supply is also regulated via the linear voltage regulator,
U2. The 3.3 V output of this regulator is used to supply the
JTAG programming interface. This device does not supply the
ADuC7060 device.
When on, the LED (D4) indicates that a valid 2.5 V supply is
driven from the regulator circuit. All active components are
decoupled with 0.1 μF capacitors at device supply pins to
ground.
RS-232 INTERFACE
The ADuC7060 (U1) P1.1 and P1.0 lines are connected to the
RS-232 interface cable via Connector J4. The interface cable
generates the required level shifting to allow direct connection
to a PC serial port. Ensure that the cable supplied is connected
to the board correctly, that is, DVDD is connected to DVDD
and DGND is connected to DGND.
EMULATION INTERFACE
Nonintrusive emulation and download are possible on the
ADuC7060 via JTAG by connecting a JTAG emulator to the
J5 connector.
CRYSTAL CIRCUIT
The board is fitted with a 32.768 kHz crystal, from which the
on-chip PLL circuit can generate a 10.24 MHz clock.
EXTERNAL REFERENCE (ADR280)
The external 1.2 V reference chip, ADR1, has two functions.
• It is provided on the evaluation board to demonstrate the
external reference option of the ADuC7060.
• It can also be used as an input source to AIN1, if required.
RESET/DOWNLOAD/INT0 PUSH BUTTONS
The
INT0
push button is referred to as the
IRQ0
push button in
the ADuC7060/ADuC7061 data sheet. Note that this is the
same push button and only differs in name.
A reset push button is provided to allow the user to reset the
part manually. When pressed, the reset pin of the ADuC7060 is
pulled to DGND. Because the
RESET
pin on the ADuC7060 is
Schmidt-triggered internally, there is no need to use an external
Schmidt trigger on this pin.
When pressed, the
INT0
push button switch drives P0.4/IRQ0
high. This can be used to initiate an External Interrupt 0.
To enter serial download mode, pull the NTRST/
BM
pin
low while reset is toggled. On the evaluation board, serial
download mode can be easily initiated by holding down the
serial download push button (S3) while pressing and releasing
the reset button (S1).
P1-P3P4-P6P7-P9P10-P12

EVAL-ADUC7060QSPZ

Mfr. #:
Buy EVAL-ADUC7060QSPZ
Manufacturer:
Analog Devices Inc.
Description:
QUICKSTART PLUS ADUC7060 EVAL BD
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet