Panasonic Corporation 2013©
Panasonic Corporation Automation Controls Buisiness Division
industrial.panasonic.com/ac/e/
AXK(5(S)/6(S))
–5–
ACCTB22E 201309-T
SPECIFICATIONS
1. Characteristics
2. Material and surface treatment
Item
Specifications
Conditions
3mm, 3.5mm type
4mm, 4.5mm, 5mm,
5.5mm, 6mm, 6.5mm type
7mm, 8mm, 9mm type
Electrical
characteristics
Rated current 0.5A/terminal (Max. 10A) 0.5A/terminal (Max. 16A)
Rated voltage 60V AC/DC
Breakdown voltage 150V AC for 1 min. Detection current: 1mA
Insulation resistance Min. 1000MΩ Using 500V DC megger
Contact resistance Max. 60mΩ Max. 80mΩ
Based on the contact resistance
measurement method specified
by JIS C 5402.
Mechanical
characteristics
Composite insertion
force
Max. 0.785N × no. of pins (initial)
Composite removal
force
Min. 0.0588N × no. of pins
Contact holding force Min. 0.98N/pin contacts
Measuring the maximum force.
As the contact is axially pull out.
Environmental
characteristics
Ambient temperature –55°C to +85°C No freezing at low temperatures
Soldering heat
resistance
Max. peak temperature of 260°C
(on the surface of the PC board around the connector terminals)
Infrared reflow soldering
300°C within 5 sec., 350°C within 3 sec. Soldering iron
Thermal shock
resistance (header
and socket mated)
5 cycles, insulation resistance min. 100MΩ,
contact resistance max. 60mΩ
5 cycles, insulation resistance
min. 100MΩ,
contact resistance
max. 80mΩ
Conformed to MIL-STD-202F,
method 107G
Humidity resistance
(header and socket
mated)
120 hours, insulation resistance min. 100MΩ,
contact resistance max. 60mΩ
120 hours, insulation resistance
min. 100MΩ,
contact resistance
max. 80mΩ
Bath temperature 40±2°C,
humidity 90 to 95% R.H.
Saltwater spray
resistance (header
and socket mated)
24 hours, insulation resistance min. 100MΩ,
contact resistance max. 60mΩ
24 hours, insulation resistance
min. 100MΩ,
contact resistance
max. 80mΩ
Bath temperature 35±2°C,
saltwarter concentration 5±1%
H2S resistance
(header and socket
mated)
48 hours, contact resistance max. 60mΩ
48 hours, contact resistance
max. 80mΩ
Bath temperature 40±2°C,
gas concentration 3±1 ppm,
humidity 75 to 80% R.H.
Lifetime
characteristics
Insertion and removal
life
50 times
Repeated insertion and removal
speed of max. 200 times/hours
Unit weight
P5K 3mm 30 pin contacts
P5KS 4mm 30 pin contacts
Socket: 0.17g Header: 0.09g
Socket: 0.18g Header: 0.16g
Part name
Mated height 3mm, 3.5mm, 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 6.5mm, 7mm, 8mm, 9mm
Material Surface treatment
Molded portion Heat-resistant resin (UL94V-0) —
Contact/post Copper alloy
Contact portion: Ni plating on base, Au plating on surface
Te r minal portion: Ni plating on base, Au plating on surface (Except for thick of terminal)
The section close to the soldering portion has a nickel barrier.
(The nickel base is exposed.)
Order
Temperature
(°C)
Time
(minutes)
1
2
3
4
–55
85
–55
0
−3
30
Max. 5
30
Max. 5
+3
0
0
−3
Partly to Be Discontinued:P5KS 120, 130, 160 pin contacts
Last time buy:September 30, 2014
