650R-11ILFT

DATASHEET
NETWORKING CLOCK SYNTHESIZER ICS650-11
IDT®
NETWORKING CLOCK SYNTHESIZER 1
ICS650-11 REV D 012313
Description
The ICS650-11 is a low cost, low jitter, high performance
clock synthesizer customized for BroadCom. Using analog
Phase-Locked Loop (PLL) techniques, the device accepts a
25.0MHz clock or fundamental mode crystal input to
produce multiple output clocks of 25.0MHz, 33.33MHz,
66.66MHz, 100.0MHz, and 133.33MHz. All output clocks
are frequency locked together. The ICS650-11 outputs all
have 0 ppm synthesis error.
Features
Packaged in 20-pin narrow SSOP, Pb-free
25.00 MHz fundamental crystal or clock input
Five fixed output clocks of 25.0 MHz, 33.33MHz,
66.66MHz, 100.0MHz, and 133.33MHz
Zero ppm synthesis error in all clocks
Ideal for BroadCom BCM5600/BCM5400 chipset
Full CMOS output swing
Advanced, low power, sub-micron CMOS process
3.0V to 5.5V operating voltage
Industrial temperature range
Block Diagram
ICS650-11
NETWORKING CLOCK SYNTHESIZER SYNTHESIZERS
IDT®
NETWORKING CLOCK SYNTHESIZER 2
ICS650-11 REV D 012313
Pin Assignment
Pin Descriptions
Pin
Number
Pin
Name
Pin
Type
Pin Description
1 GND Power Connect to ground
2 X2 XO Crystal connection. Connect to a 25MHz crystal or leave unconnected for a
clock input.
3 X1 XI Crystal connection. Connect to a 25MHz fundamental crystal or clock input.
4 VDD Power Connect to +3.3V or +5V. Must be same as other VDDs.
5 GND Power Connect to ground
6 GND Power Connect to ground
7 DC Don’t connect. Do not connect this pin to anything.
8 DC Don’t connect. Do not connect this pin to anything.
9 DC Don’t connect. Do not connect this pin to anything.
10 100M Output 100.0MHz clock output.
11 GND Power Connect to ground
12 66.66M Output 66.66MHz clock output.
13 25M Output 25.0MHz clock output.
14 GND Power Connect to ground
15 VDD Power Connect to +3.3V or +5V. Must be same as other VDDs.
16 VDD Power Connect to +3.3V or +5V. Must be same as other VDDs.
17 33.33M Output 33.33MHz clock output.
18 133.33M Output 133.33MHz clock output.
19 DC Don’t connect. Do not connect this pin to anything.
20 DC Don’t connect. Do not connect this pin to anything.
ICS650-11
NETWORKING CLOCK SYNTHESIZER SYNTHESIZERS
IDT®
NETWORKING CLOCK SYNTHESIZER 3
ICS650-11 REV D 012313
External Components
The ICS650-11 requires a minimum number of external
components for proper operation. Decoupling capacitors of
0.01ìF should be connected between each VDD and GND
on Pins 4 and 6, and Pins 16 and 14, as close to the
ICS650-11 as possible. A series termination resistor of 33
may be used for each clock output. The 25.00 MHz crystal
must be connected as close to the chip as possible. The
crystal should be a fundamental mode (do not use third
overtone), parallel resonant. Crystal capacitors should be
connected from pins X1 to ground and X2 to ground to
optimize the initial accuracy. The value of these capacitors
is given by the following equation, where C
L
is the crystal
load capacitance: Crystal caps (pF) = (C
L
-6) x 2. So for a
crystal with 16 pF load capacitance, two 20 pF caps should
be used.

650R-11ILFT

Mfr. #:
Manufacturer:
IDT
Description:
Clock Drivers & Distribution SYSTEM PERIPHERAL CLOCK SOURCE
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet