OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

FSAB20PH60

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P16
4 www.fairchildsemi.com
FSAB20PH60 Rev. A
FSAB20PH60 Smart Power Module for Partial Switching Converter
Absolute Maximum Ratings (T
J
= 25°C, Unless Otherwise Specified)
Converter Part
Note:
1. The maximum junction temperature rating of the power chips integrated within the module is 150 °C(@T
C
≤ 100°C). However, to insure safe operation, the average junction
temperature should be limited to T
J(ave)
≤ 125°C (@T
C
≤ 100°C)
Control Part
Total System
Symbol Parameter Conditions Rating Units
V
i
Input Supply Voltage Applied between R-S 276 V
V
i(Surge)
Input Supply Voltage (Surge) Applied between R-S 500 V
V
PN
Output Voltage Applied between P-N 400 V
V
PN(surge)
Output Voltage (Surge) Applied between P-N 500 V
V
CES
Collector-emitter Voltage IGBT 600 V
V
RRM
Repetitive Peak Reverse Voltage Diode 600 V
I
i
Input Current (100% Load) T
C
≤ 90°C, V
O
= 280V, f
PWM
= 60Hz 11 A
RMS
I
i
Input Current (130% Load) T
C
≤ 90°C, V
O
= 280V, f
PWM
= 60Hz 14 A
RMS
T
J
Operating Junction Temperature (Note 1) -20 ~ 125 °C
Symbol Parameter Conditions Rating Units
V
CC
Control Supply Voltage Applied between V
CC
- COM 20 V
V
IN
Input Signal Voltage Applied between IN
(R)
, IN
(S)
- COM -0.3~V
CC
+0.3 V
V
FO
Fault Output Supply Voltage Applied between V
FO
- COM -0.3~V
CC
+0.3 V
I
FO
Fault Output Current Sink Current at V
FO
Pin 5 mA
V
SC
Current Sensing Input Voltage Applied between C
SC
- COM -0.3~V
CC
+0.3 V
Symbol Parameter Conditions Rating Units
T
C
Module Case Operation Temperature -20°C < T
J
< 125°C, See Fig.2 -20 ~ 100 °C
T
STG
Storage Temperature -40 ~ 125 °C
V
ISO
Isolation Voltage 60Hz, Sinusoidal, AC 1 minute, Connection
Pins to DBC
2500 V
rms
5 www.fairchildsemi.com
FSAB20PH60 Rev. A
FSAB20PH60 Smart Power Module for Partial Switching Converter
Absolute Maximum Ratings
Thermal Resistance
Note:
2. For the measurement point of case temperature(T
C
), please refer to Figure 2.
Electrical Characteristics (T
J
= 25°C, Unless Otherwise Specified)
Main Circuit Part
Note:
3. t
ON
and t
OFF
include the propagation delay time of the internal drive IC. t
C(ON)
and t
C(OFF)
are the switching time of IGBT itself under the given gate driving condition internally.
For the detailed information, please see Figure 4.
Figure 4. Switching Time Definition
Symbol Parameter Conditions Min. Typ. Max. Units
R
th(j-c)Q
Junction to Case Thermal
Resistance
Each IGBT under Operating Condition - - 2.8 °C/W
R
th(j-c)D
Each Diode under Operating Condition - - 2.6 °C/W
Symbol Item Conditions Min. Typ. Max. Units
V
CE(SAT)
Collector-Emitter Saturation
Voltage
V
CC
= V
BS
=15V
V
IN
= 5V
I
C
= 6.5A, T
J
= 25°C - 2.1 2.6 V
V
FM
Diode Forward Voltage V
IN
= 0V I
C
= 20A, T
J
= 25°C - 1.1 1.5 V
t
ON
Switching Times V
PN
= 300V, V
CC
= V
BS
= 15V
I
C
= 6.5A
V
IN
= 0V ↔ 5V, Inductive Load
(Note 3)
-0.48- µs
t
C(ON)
-0.85- µs
t
OFF
-0.56- µs
t
C(OFF)
-0.10- µs
t
rr
-1.35- µs
I
CES
Collector - Emitter
Leakage Current
V
CE
= V
CES
- - 250 µA
I
R
Diode Leakage Current V
R
= V
RRM
- - 250 µA
V
CE
I
C
V
IN
t
OFF
t
C(OFF)
V
IN(OFF)
10% V
CE
10% I
C
V
CE
I
C
V
IN
t
ON
t
C(ON)
V
IN(ON)
10% I
C
10% V
CE
90% I
C
100% I
C
t
rr
120% I
C
6 www.fairchildsemi.com
FSAB20PH60 Rev. A
FSAB20PH60 Smart Power Module for Partial Switching Converter
Electrical Characteristics (T
J
= 25°C, Unless Otherwise Specified)
Control Part
Note:
4. Over current protection is functioning only for the low-side IGBT.
5. The fault-out pulse width t
FOD
depends on the capacitance value of C
FOD
according to the following approximate equation : C
FOD
= 18.3 x 10
-6
x t
FOD
[F]
Recommended Operating Conditions
Note:
6. Regarding the switching method of FSAB20PH60, it follows the control method of the typical partial-switching power factor correction circuit as shown in Figure 5.
Symbol Parameter Conditions Min. Typ. Max. Units
I
QCCL
Quiescent V
CC
Supply
Current
V
CC
= 15V
IN
(L)
= 0V
V
CC(L)
- COM - - 23 mA
V
FOH
Fault Output Voltage V
SC
= 0V, V
FO
Circuit: 4.7kΩ to 5V Pull-up 4.5 - - V
V
FOL
V
SC
= 1V, V
FO
Circuit: 4.7kΩ to 5V Pull-up - - 0.8 V
V
SC(ref)
Short Circuit Trip Level V
CC
= 15V (Note 4) 0.45 0.5 0.55 V
UV
CCD
Supply Circuit Under-
Voltage Protection
Detection Level 10.7 11.9 13.0 V
UV
CCR
Reset Level 11.2 12.4 13.2 V
t
FOD
Fault-out Pulse Width C
FOD
= 33nF (Note 5) 1.0 1.8 - ms
V
IN(ON)
ON Threshold Voltage Applied between IN
(R)
, IN
(S)
- COM 3.0 - - V
V
IN(OFF)
OFF Threshold Voltage - - 0.8 V
R
TH
Resistance of Thermistor @ T
C
= 25°C (Note Fig. 10) - 50 - kΩ
@ T
C
= 80°C (Note Fig. 10) - 5.76 - kΩ
Symbol Parameter Condition
Value
Units
Min. Typ. Max.
V
i
Input Supply Voltage Applied between R - S 187 - 276 V
rms
V
PN
Output Voltage Applied between P - N - 280 400 V
V
CC
Control Supply Voltage Applied between V
CC
- COM 13.5 15 16.5 V
f
PWM
PWM Input Signal T
C
≤ 100°C, T
J
≤ 125°C, Per IGBT (Note 6) - 60 - Hz
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P16

FSAB20PH60

Mfr. #:
Buy FSAB20PH60
Manufacturer:
ON Semiconductor / Fairchild
Description:
Motor / Motion / Ignition Controllers & Drivers HIGH VOLTAGE
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet