2008152-1 Datasheet 2008152-1 | P1-P3

Wire

Release

Latch

White

Wire

Black

Wire

Strain-Relief

Receptacle Assembly

Plug Assembly

Plug

Wire

Receptacle

White

Wire

Black

Wire

Strain-Relief

CONNECTOR

PART

NUMBER

DESCRIPTION

2008149-1 3-Position Plug

2008150-1 3-Position Receptacle

2008150-1 Pre-Mated Plug and Receptacle

2008149-2 3-Position Plug (Orange)

2008150-2 3-Position Receptacle (Orange)

2008150-2 Pre-Mated Plug and Receptacle (Orange)

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

1 of 3

Instruction Sheet

TOOLING ASSISTANCE CENTER

1-800-722-1111



PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

408-10154

LIGHT-N-LOK* Connectors

13 MAR 12 Rev D

Figure 1

1. INTRODUCTION

This instruction sheet covers the assembly procedures

of LIGHT-N-LOK Connectors 2008149-[ ], 2008150-[ ],

and 2008152-[ ].

NOTE

For detailed application requirements, refer to

Application Specification 114-13207.

NOTE

Dimensions in this instruction sheet are in

millimeters [with inches in brackets]. Figures and

illustrations are f

or reference only and are not

drawn to scale.

Reason for revision are given

in Section 7, REVISION

SUMMARY.

2. DESCRIPTION

These connectors consist of a plug and a receptacle.

Customers may order complete cable assemblies

from TE. Refer to the table in Figure 1.

3. ASSEMBLY PROCEDURE

CAUTION

In the field, these connectors must be assembled

by a qualified electrician in accordance with

national and local electrical cod

es and the following

instructions.

Select the proper connector part number for your

oduction requirements.

When selecting connectors 2008149-[ ], 2008150-[ ],

2008152-[ ] refer to the following procedures:

1. Strip wires with 18 AWG solid copper conductors

ving a maximum insulation diameter of 2.18 mm

[.086 in.] to the dimensions provided in Figure 2.

Plug

Connector

Strip

Gage

Insulation

Conductor

9.53±0.80 [.375±.031]

Recommended Strip Length

Figure 2

2. Insert each stripped wire into an insertion hole in

the back of the plug or receptacle until bottomed.

For field wiring, black and white wires must be

inserted into corresponding holes marked "B" or

"W". This "Wire-Trap Termination" method removes

the need for application termination tooling. See

Figure 3.

NOTE

408-10154

2 of 3

Rev D

Pull back gently on the wires to ensure they have

latched fully into the connectors.

Wire Bottomed in 

Connector Assembly

Figure 3

3. Pull the wire down through the slot in the strain-

relief. See Figure 4.

Figure 4

4. Rotate the wire 90°. See Figure 5.

Figure 5

5. Dress the wire 180° to complete the process. See

Figure 6.

Wire Dressedin Slots at 180°

Figure 6

6. Apply optional approved flammability rated tape

or clamp to organize the wires. See Figure 7.

Optional Tape or Clamp

May Be Applied

Figure 7

4. CONNECTOR MATING

Align the polarized mating faces of the connectors,

and push the connectors together. DO NOT force the

connectors to mate. When fully mated, the connectors

must appear bottomed with each other and flush at the

point of engagement. An audible and tactile "click" will

be heard and felt. See Figure 8.

408-10154

3 of 3

Rev D

5. CONNECTOR UNMATING

DANGER

STOP

To reduce risk of electric shock, DISCONNECT the

electrical supply before unmating the connectors

To unmate the connectors, squeeze the release

tches on either side of the plug and pull back until

both connectors separate from each other.

CAUTION

Do NOT pull on wires when unmating the

connectors.

6. REPLACEMENT AND REPAIR

The contacts and connectors, are not repairable. DO

NOT use damaged or defective contacts or

connectors. DO NOT remove the wire and re-

terminate contacts.

7. REVISION SUMMARY

Since the previous release of these instructions,

product has been added to Figure 1.

10 [.394] Max

Plug Receptacle

Tape or Clamp Tape or Clamp

Figure 8

P1-P3

2008152-1

Mfr. #:

Buy 2008152-1

Manufacturer:

TE Connectivity / AMP Connectors

Description:

Lighting Connectors 3 POS LIGHT-N-LOK

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet

2008152-1