RPM873-E4

RPM873
Photo Link Module
Rev.B 4/6
zElectrical characteristics (V
CC=3V, VLEDA=3V, Ta=25°C)
Parameter Symbol Min. Typ. Max. Unit Conditions
Consumption current 1 I
CC
1
I
CC
2
VPDH
VPDL
IPDH
IPDL
75
µA
PWDOWN=V
CC
[V]
Waiting mode, At no input light
PWDOWN mode, At no input lightConsumption current 2
Transmission rate
PWDOWN input high voltage
PWDOWN input low voltage
PWDOWN input high current
PWDOWN input low current
TXD input high voltage
TXD input low voltage
RXD output high voltage
RXD output rise time
RXD output fall time
RXD output pulse width
Receiver latency time
RXD output low voltage
TXD input high current
TXD input low current
LED anode current
0.01
0
2.4
V
CC
0.55
V
CC
0.55
0.55
99
µA
0.2
kbps115.2
V
V
<Transmitter>
<Receiver>
VTXH
VTXL
ITXH
ITXL
ILEDA
VRXH
VRXL
tRR
tFR
tRT
twRXD
PWDOWN=0 [V]
TXD=V
CC
[V]
TXD=0 [V]
0
1.0
0
2.5
1.0
0
1.5
V
CC
0.4
0
1.0
5
0
30.5
35
35
2.3
100
µA
1.0
µA
1.0
V
V0.55
µA
µA
mA
V
V
ns
ns
µs
µs
10
1.0
0.4
4.2
200
IRXH= −200µA
IRXL= 200µA
C
L
=15pF
C
L
=15pF
C
L
=15pF, 2.4 to 115.2kbps
zOptical characteristics (V
CC=3V, VLEDA=3V, Ta=25°C)
1. This product is not designed for protection against radioactive rays.
2. This product does not include laser transmitter.
3. This product include one PIN photo diode.
4. This product dose not include optical load.
Parameter Symbol Min. Typ. Max. Unit Conditions
Peak wave length
λP
IE1
θL / 2
θD / 2
TLEDmax
Tr / Tf
Tj
Eemin
870 nm
15° θ
L
15°
TXD=V
CC
10% to 90%
Intensity 1
Half-angle
Rise time / Fall time
Optical over shoot
Edge jitter
Minimum irradiance in angular range
Half-angle
Maximum emitting time
850
104
±18
900
mW / Sr26
TWLED
TXD=1.63µs pulse input
Opticcal pulse width 1.631.42
µs
2.02
µW / cm
2
ns
µs
±30
100
48
40
±15
10
%25
ns40
6.8
Eemax
15° θ
L
15°
Maximum irradiance in angular range
mW / cm
2
500
120
˚C
˚C
15° θ
L
15°
<
<
<
<
<
<
RPM873
Photo Link Module
Rev.B 5/6
zTiming chart
less than 48 µs
(emitting)
more than 48 µs
approximately 48 µs
less than 2.3 µs more than 2.3 µs
approximately 2.3 µs
pull up to V
CC
at approximately
300 k
(emitting)
(emitting)
(Emitting side)
(Detecting side)
TXD
(7pin)
Internal LED
(Light output)
Light input
RXD
(6pin)
PWDOWN
(5pin)
zNotes
1) VLEDA (8pin) and V
CC (3pin)
Other power source can be used difference between VLEDA and V
CC.
2) Caution in designing board lay-out
To get maximum potential from RPM873, please keep in mind following instruction.
The line of RXD (6pin) should be connected at backside via through hole close to RPM873 pin lead.
Better not to be close to photo diode side (1pin).
This is to minimize feedback supplied to photo diode from RXD.
Better to be placed more than 1.0cm in radius from photo diode (pin1 side) and also away from the parts which
generate noise, such as DC / DC converter.
As for C1 between 3-4pin should be placed close to RPM873.
3) Notes
Please be sure to set up the TXD (7pin) input to be “L” (under 0.55V) except transmitting data
(for<90µs, ON duty<20%)
Power down current might increase if exposed by strong light (ex. direct sunlight) at power down mode.
Please use by the signal format which is specified by lrDA Ver1.2 (2.4k to 115.2kbps).
There might be on error if used by different signal format.
4) Eye Safe
IEC825-1 (EN60825-1) Class 1 Eye Safe.
RPM873
Photo Link Module
Rev.B 6/6
z Dimensions Diagram (Unit : mm)
RSLP8
R1.0
R1.1
0.78
0.76
0.37±0.10
0.95
3.8
1
1
8
LEDPin PD
2
1
2.72
0.8
7.6
5.6
P0.95 × 7=6.65
2.49

RPM873-E4

Mfr. #:
Manufacturer:
Description:
IC IRDA IR COMMUNICATION MODULE
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet