SMBus Table: Output Enable Register
1
Byte 0 Name Control Function Type 0 1 Default
Bit 7
DIF OE7 Output Enable RW Pin Control 1
Bit 6
DIF OE6 Output Enable RW Pin Control 1
Bit 5
DIF OE5 Output Enable RW Pin Control 1
Bit 4
DIF OE4 Output Enable RW Pin Control 1
Bit 3
DIF OE3 Output Enable RW Pin Control 1
Bit 2
DIF OE2 Output Enable RW Pin Control 1
Bit 1
DIF OE1 Output Enable RW Pin Control 1
Bit 0
DIF OE0 Output Enable RW Pin Control 1
SMBus Table: Spread Spectrum and Vhigh Control Register
Byte 1 Name Control Function Type 0 1 Default
Bit 7
SSENRB1 SS Enable Readback Bit1
R
Latch
Bit 6
SSENRB1 SS Enable Readback Bit0
R
Latch
Bit 5
SSEN_SWCNTRL Enable SW control of SS RW
SS controlled by
latch (B1[7:6]).
Values in B1[4:3]
control SS amount.
0
Bit 4
SSENSW1 SS Enable Software Ctl Bit1
RW
1
0
Bit 3
SSENSW0 SS Enable Software Ctl Bit0
RW
1
0
Bit 2
X
Bit 1
AMPLITUDE 1 RW 00 = 0.6V 01= 0.68V 1
Bit 0
AMPLITUDE 0 RW 10 = 0.75V 11 = 0.85V 0
SMBus Table: DIF Slew Rate Control Register
Byte 2 Name Control Function Type 0 1 Default
Bit 7
SLEWRATESEL DIF7 Adjust Slew Rate of DIF7 RW Slow Setting Fast Setting 1
Bit 6
SLEWRATESEL DIF6 Adjust Slew Rate of DIF6 RW Slow Setting Fast Setting 1
Bit 5
SLEWRATESEL DIF5 Adjust Slew Rate of DIF5 RW Slow Setting Fast Setting 1
Bit 4
SLEWRATESEL DIF4 Adjust Slew Rate of DIF4 RW Slow Setting Fast Setting 1
Bit 3
SLEWRATESEL DIF3 Adjust Slew Rate of DIF3 RW Slow Setting Fast Setting 1
Bit 2
SLEWRATESEL DIF2 Adjust Slew Rate of DIF2 RW Slow Setting Fast Setting 1
Bit 1
SLEWRATESEL DIF1 Adjust Slew Rate of DIF1 RW Slow Setting Fast Setting 1
Bit 0
SLEWRATESEL DIF0 Adjust Slew Rate of DIF0 RW Slow Setting Fast Setting 1
Note: See "Low -Power HCSL Outputs" table for slew rates.
SMBus Table: Nominal Vhigh Amplitude Control/ REF Control Register
Byte 3 Name Control Function Type 0 1 Default
Bit 7
RW 00 = Slowest 01 =Slow 0
Bit 6
RW 10 = Fast 11 = Fastest 1
Bit 5
REF Power Down Function Wake-on-Lan Enable for REF RW
REF disabled in
Power Down
REF runs in Power
Down
0
Bit 4
REF OE REF Output Enable RW
Disabled
1
Enabled 1
Bit 3
X
Bit 2
X
Bit 1
X
Bit 0
X
1. The disabled state depends on Byte11[1:0]. '00' = Low, '01'=HiZ, '10'=Low, '11'=HIgh
Byte 4 is Reserved
Reserved
00' for SS_EN= 0,
'11 for SS_EN = '1'
00' = SS Off, '01' = -0.25% SS,
'10' = Reserved, '11'= -0.5% SS
Reserved
Controls Output Amplitude
1. Spread must be selected OFF or ON with the hardware latch pin. These bits should not be used to turn spread ON or OFF after
power up. These bits can be used to change the spread amount, and B1[5] must be set to a 1 for these bits to have any effect on
the part. If These bits are used to turn spread OFF or ON, the system will need to be reset.
See B11[1:0]
1. A low on these bits will overide the OE# pin and force the differential output to the state indicated by B11[1:0] (Low/Low default)