CY7C130, CY7C130A
CY7C131, CY7C131A
Document Number: 38-06002 Rev. *H Page 5 of 22
Maximum Ratings
[5]
Exceeding maximum ratings may shorten the useful life of the
device. User guidelines are not tested.
Storage temperature ................................ –65 C to +150
C
Ambient temperature with
power applied ........................................... –55 C to +125 C
Supply voltage to ground potential
(pin 48 to pin 24)...........................................–0.5 V to +7.0 V
DC voltage applied to outputs
in high Z State...............................................–0.5 V to +7.0 V
DC input voltage...........................................–3.5 V to +7.0 V
Output current into outputs (LOW) ..............................20 mA
Static discharge voltage.......................................... > 2001 V
(per MIL-STD-883, method 3015)
Latch-up current .................................................... > 200 mA
Operating Range
Range Ambient Temperature V
CC
Commercial 0 C to +70 C 5 V ± 10%
Industrial –40 C to +85 C 5 V ± 10%
Military
[6]
–55 C to +125 C 5 V ± 10%
Electrical Characteristics
Over the Operating Range
[7]
Parameter Description Test Conditions
7C131-15
[4]
7C131A-15
7C141-15
7C130-30
[4]
7C130A-30
7C131-25,30
7C140-30
7C141-25,30
7C130-35,45
7C131-35,45
7C140-35,45
7C141-35,45
7C130-55
7C131-55
7C140-55
7C141-55
Unit
Min Max Min Max Min Max Min Max
V
OH
Output HIGH voltage V
CC
= Min, I
OH
= –4.0 mA 2.4 – 2.4 – 2.4 – 2.4 – V
V
OL
Output LOW voltage I
OL
= 4.0 mA – 0.4 – 0.4 – 0.4 – 0.4 V
I
OL
= 16.0 mA
[8]
– 0.5 – 0.5 – 0.5 – 0.5 V
V
IH
Input HIGH voltage 2.2 – 2.2 – 2.2 – 2.2 – V
V
IL
Input LOW voltage – 0.8 – 0.8 – 0.8 – 0.8 V
I
IX
Input leakage current GND < V
I
< V
CC
–5 +5 –5 +5 –5 +5 –5 +5 µA
I
OZ
Output leakage current GND < V
O
< V
CC
, output disabled –5 +5 –5 +5 –5 +5 –5 +5 µA
I
OS
Output short circuit
current
[9, 10]
V
CC
= Max,
V
OUT
= GND
– –350 – –350 – –350 – –350 mA
I
CC
V
CC
operating supply
current
CE = V
IL
, outputs
open, f = f
MAX
[11]
Commercial – 190 – 170 – 120 – 110 mA
I
SB1
Standby current both
ports, TTL inputs
CE
L
and CE
R
> V
IH
,
f = f
MAX
[11]
Commercial – 75 – 65 – 45 – 35 mA
I
SB2
Standby current one
port, TTL inputs
CE
L
or CE
R
> V
IH
,
active port outputs
open, f = f
MAX
[11]
Commercial – 135 – 115 – 90 – 75 mA
I
SB3
Standby current both
ports, CMOS inputs
Both ports CE
L
and
CE
R
> V
CC
– 0.2 V,
V
IN
> V
CC
– 0.2 V
or V
IN
< 0.2 V, f = 0
Commercial
– 15 – 15 – 15 – 15 mA
I
SB4
Standby current one
port, CMOS inputs
One port CE
L
or
CE
R
> V
CC
– 0.2 V,
V
IN
> V
CC
– 0.2 V
or V
IN
< 0.2 V,
active port outputs
open, f = f
MAX
[11]
Commercial – 125 – 105 – 85 – 70 mA
Shaded areas contain preliminary information.
Notes
5. The voltage on any input or I/O pin cannot exceed the power pin during power up.
6. T
A
is the “instant on” case temperature
7. See the last page of this specification for Group A subgroup testing information.
8. BUSY
and INT pins only.
9. Duration of the short circuit should not exceed 30 seconds.
10. This parameter is guaranteed but not tested.
11. At f = f
MAX
, address and data inputs are cycling at the maximum frequency of read cycle of 1/t
RC
and using AC Test Waveforms input levels of GND to 3 V.