11
FN8190.5
September 14, 2015
Power-up and Down Requirements
The are no restrictions on the power-up or power-down
conditions of V
CC
and the voltages applied to the poten-
tiometer pins provided that V
CC
is always more positive than
or equal to V
H
, V
L
, and V
W
, i.e., V
CC
V
H
, V
L
, V
W
.
The V
CC
power-up spec is always in effect.
Absolute Maximum Ratings Thermal Information
Supply Voltage (V
CC
Limits)
X9401 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V ±10%
X9401-2.7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Voltage on SCK, SCL or any address input
with respect to V
SS
: . . . . . . . . . . . . . . . . . . . . . . . . . . . -1V to +7V
V = |(V
H
–V
L
)| . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
Temperature Under Bias . . . . . . . . . . . . . . . . . . . . .-65C to +135C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range
Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Industrial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
Analog Specifications (Over recommended operating conditions unless otherwise stated.)
SYMBOL PARAMETER TEST CONDITION
MIN
(Note 10)
TYP MAX
(Note 10) UNIT
R
TOTAL
End to End resistance Tolerance -20 +20 %
Power Rating +25°C, each pot 50 mW
I
W
Wiper Current -6 +6 mA
R
W
Wiper Resistance I
W
= (V
H
- V
L
)/R
TOTAL
V
CC
= 5V 150 500
V
TERM
Voltage on any V
H
or V
L
Pin V
SS
V
CC
V
Noise Ref: 1kHz -120 dBV
Resolution 1.6 %
Absolute Linearity (Note 7) V
W(n)(actual)
- V
W(n)(expected)
-1 +1 MI
(Note 9)
Relative Linearity (Note 8) V
w(n+1)
- [V
w(n)
+ MI] -0.2 +0.2 MI
(Note 9)
Temperature Coefficient of R
TOTAL
V(R
H
) = V
CC
, V(R
L
) = V
SS
300 ppm/°C
Ratiometric Temperature Coefficient 20 ppm/°C
C
H
/C
L
/C
W
Potentiometer Capacitances See Macro model 10/10/25 pF
I
AL
R
H
, R
L
, R
W
Leakage Current V
IN
= V
SS
Device is in Stand-by mode. 0.1 10 µA
NOTES:
7. Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a
potentiometer.
8. Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentiometer. It is
a measure of the error in step size.
9. MI = RTOT/63 or (V
H
- V
L
)/63, single pot.
10. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by
characterization and are not production tested.
X9401