DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
DO NOT
SCALE FROM
THIS PRINT
RPBE-XX-XX-X
No OF PORTS
-01, -02
LEAD STYLE
-01: RIGHT ANGLE
PLATING SPECIFICATION
-E: SELECTIVE, 0.00127 MIN GOLD
ON CONTACT, FLASH GOLD
ON TAIL
"A"
REF (SEE TABLE 1)
12.50
REF
.492
23.00
REF
.906
7.50 .295
REF
'G'
C
L
C
L
01 08
"C"
REF (SEE TABLE 1)
9.53
REF
.375
7.47
REF
.294
3.51
REF
.138
"B"
-
0.18
+
0.20
(SEE TABLE 1 & NOTE 11)
"A"
"A"
C
L
MS-632-375-P-P-S
(SEE NOTE 8)
RPBE-01
RPBES-01
EPOXY-RPBE-01
OR-107-01
DCN-01-06-32
C
L
FIG 1
RPBE-01-01-E SHOWN
0.81
REF
.032
5.31
±0.51
.209
±.020
17.85
-
0.18
+
0.20
.703
-
.007
+
.008
(SEE NOTE 11)
SECTION "A"-"A"
OR-108-01
MODS-A-8P8C-E-02-S-C5
C
C
C
DETAIL 'G'
SCALE 20 : 1
SEE NOTE 13
C
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN MILLIMETERS.
TOLERANCES ARE:
DECIMALS ANGLES
X.X:
0.3 [.01] 2
X.XX:
0.13 [.005]
X.XXX:
0.051 [.0020]
MATERIAL:
SEAL RECTANGULAR ETHERNET
BY:
RPBE-XX-XX-X
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
T NEWTON
11/17/2009
4
1
SHEET SCALE: 3:2
INSULATOR: LCP, COLOR: BLACK
CONTACT: PHOS BRONZE
SEAL: NBR
SHIELD: COPPER ALLOY
SCREW: STAINLESS STEEL
NUT: STAINLESS STEEL
O-RING: SILICONE
EPOXY: DIELECTRIC SILICON
F:\DWG\MISC\MKTG\RPBE-XX-XX-X-MKT.SLDDRW
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. BURR ALLOWANCE: 0.038[.0015] MAX.
3. MINIMUM PUSHOUT FORCE: 4.4N[1.00 LB].
4. MAXIMUM ALLOWABLE BOW: 0.05[.002] MM/MM AFTER ASSEMBLY.
5. PANEL THICKNESS: 0.08[.030] - 3.96[.156], RECOMMENDED PANEL
CUT OUT ON SHEET 3.
6. SEE EPOXY-RPBE-XX FOR CURING INSTRUCTIONS.
7. PARTS TO BE OVEN CURED AT 200°C FOR 10 MINUTES.
8. SEALING O-RING IS INCLUDED WITH MS-632-375-P-P-S.
9. ALL PARTS MUST BE PACKAGED IN TUBES.
10. REQUIRED TORQUE ON MS-632-375-P-P-S FOR RPBE-01-01-E: 0.32Nm±0.07[45IN-OZ±10]
FOR RPBE-02-01-E: 0.16Nm±0.04[65IN-OZ±5]
11. MEASURE O-RING IN THE CENTER OF THE PART.
12. EPOXY TO SEAL/WICK AROUND ALL WALLS/CONTACT TAILS.
13. OR-108-XX POSITION INDICATOR.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
REVISION E
