OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

TLE5014C16DXUMA1

P1-P3P4-P6P7-P9P10-P12P13-P13
Final Datasheet 4 Rev. 1.0
2018-04-04
TLE5014D
Dual Sensor Angle Output
2 Dual Sensor Angle Output
The bottom sensor element of the Product_Short is flipped relative to the orientation of the top sensor
element Therefore the rotation direction sensed by the bottom element is opposite to the top element. This
is advantageous for safety critical applications, as the two sensor elements do generally not output the same
angle. Figure 2-1 shows the output of the two sensor ICs for a given external magnetic field orientation.
Figure 2-1 Dual die angle output
For applications where an identical angle output of both ICs is desired, the rotation direction and angle offset
of one sensor IC can be reconfigured by changing the settings in the ANG_BASE register of the EEPROM.
9 IFC-2 O address coding for programming in bus mode,
channel 2 (see TLE5014 datasheet)
connect to IF3
10 IFB-2 I/O SENT / SPC / PWM / SICI interface for channel 2
11 IFA-2 - connect to GND
12 GND-2 - supply voltage, ground for channel 2
13 VDD-2 - supply voltage, positive for channel 2
14 IF3-2 I connect to IFC
15 IF2-2 I address coding for programming in bus mode,
channel 2 (see TLE5014 datasheet)
connect to GND for SENT / PWM interface
16 IF1-2 I address coding for programming in bus mode,
channel 2 (see TLE5014 datasheet)
connect to GND for SENT / PWM interface
Table 1-1 Pin Description (cont’d)
Pin No. Symbol In/Out Function
0° 90° 180°270°360°
90°
180°
270°
360°
top sensor output
bottom sensor output
external magnetic field angle
sensor output angle
Final Datasheet 5 Rev. 1.0
2018-04-04
TLE5014D
Absolute Maximum Ratings
3 Absolute Maximum Ratings
Attention: Stresses above the max. values listed here may cause permanent damage to the device. Exposure
to absolute maximum rating conditions for extended periods may affect device reliability. Maximum
ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to
the device.
Table 3-1 ESD protection
Parameter Symbol Values Unit Notes
Min. Max.
Electro-Static-Discharge
voltage (HBM), according
to
ANSI/ESDA/JEDEC JS-001
V
HBM
±4.0 kV HBM contact discharge
for pins VDD, GND, IFB;
ground pins connected
V
HBM
±2.0 kV HBM contact discharge
for all pins,
ground pins not connected
Electro-Static-Discharge
voltage (CDM), according
to JESD22-C101
V
CDM
±0.5 kV for all pins except corner pins
±0.75 kV for corner pins only
Final Datasheet 6 Rev. 1.0
2018-04-04
TLE5014D
Pre-Configured Derivatives
4 Pre-Configured Derivatives
Derivatives of the TLE5014D are available with different pre-configured register settings for specific
application (“settings”). For each derivative with such settings, the interface type is locked and cannot be
changed. Only the derivatives with such settings have been released for production by Infineon.
Other settings/parameters for other applications could be adjusted but such adjusted settings would not have
been released for production by Infineon.
Furthermore, the available safety analysis and safety manual does only include these preconfigured
derivatives.
4.1 TLE5014C16D
The sensor has SPC as predefined interface which is locked and cannot be changed.
The predefined SPC configuration of TLE5014C16D is shown below:
Following parameters and values are allowed to modify:
• SPC unit time: 1.5µs / 2.5µs
• Short serial message: enable / disable
• Rolling counter in CRC: enable /disable
• SPC ID: 0 / 1 / 2 / 3
4.2 TLE5014S16D
The sensor has SENT as predefined interface which is locked and cannot be changed.
The predefined SENT configuration of TLE5014S16D is shown below:
Following parameters and values are allowed to modify:
• Short serial message: enable / disable
• Pause pulse: enable /disable
• SENT Protocol Type: Standard / Single Secure Sensor
Table 4-1 SPC Derivative Configuration TLE5014C16D
Interface SPC unit time SPC low time SPC Trigger Short Serial Message
SPC 2.5µs 5UT constant 90UT enabled
Table 4-2 SPC Derivative Configuration TLE5014C16D
Rolling Counter Rolling Counter in CRC Look-up Table SPC ID Output driver
enabled disabled enabled, preconfigured 00
B
open drain w/
controlled slope
Table 4-3 SENT Derivative Configuration TLE5014S16D
Interface SENT unit time SENT low time SENT Protocol Type Short Serial Message
SENT 3.0µs 5UT single secure sensor enabled
Table 4-4 SENT Derivative Configuration TLE5014S16D
SENT Error Indication SENT Data Range Pause Pulse Look-up Table Output driver
error code 4091 enabled 1 ... 4088 enabled enabled, preconfigured push/pull
P1-P3P4-P6P7-P9P10-P12P13-P13

TLE5014C16DXUMA1

Mfr. #:
Buy TLE5014C16DXUMA1
Manufacturer:
Infineon Technologies
Description:
SENSOR ANGLE 360DEG GULL WING
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet