MC10EL52, MC100EL52
www.onsemi.com
4
Table 6. 100EL SERIES PECL DC CHARACTERISTICS (V
CC
= 5.0 V; V
EE
= 0 V (Note 1))
−40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Power Supply Current 21 25 21 25 24 29 mA
V
OH
Output HIGH Voltage (Note 2) 3915 3995 4120 3975 4045 4120 3975 4050 4120 mV
V
OL
Output LOW Voltage (Note 2) 3170 3305 3445 3190 3295 3380 3190 3295 3380 mV
V
IH
Input HIGH Voltage (Single-Ended) 3835 4120 3835 4120 3835 4120 mV
V
IL
Input LOW Voltage (Single-Ended) 3190 3525 3190 3525 3190 3525 mV
V
IHCMR
Input HIGH Voltage Common Mode Range
(Differential Configuration) (Note 3) D
CLK
2.6
2.5
4.6
4.2
2.6
2.5
4.6
4.2
2.6
2.5
4.6
4.2
V
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current 0.5 0.5 0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V
CC
. V
EE
can vary +0.8 V / −0.5 V.
2. Outputs are terminated through a 50 ohm resistor to V
CC
− 2.0 V.
3. V
IHCMR
min varies 1:1 with V
EE
, V
IHCMR
max varies 1:1 with V
CC
. The V
IHCMR
range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between V
PP
min and 1 V.
Table 7. 100EL SERIES NECL DC CHARACTERISTICS (V
CC
= 0 V; V
EE
= −5.0 V (Note 1))
−40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Power Supply Current 21 25 21 25 24 29 mA
V
OH
Output HIGH Voltage (Note 2) −1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV
V
OL
Output LOW Voltage (Note 2) −1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV
V
IH
Input HIGH Voltage (Single-Ended) −1165 −880 −1165 −880 −1165 −880 mV
V
IL
Input LOW Voltage (Single-Ended) −1810 −1475 −1810 −1475 −1810 −1475 mV
V
IHCMR
Input HIGH Voltage Common Mode Range
(Differential Configuration) (Note 3) D
CLK
−2.4
−2.5
−0.4
−0.8
−2.4
−2.5
−0.4
−0.8
−2.4
−2.5
−0.4
−0.8
V
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current 0.5 0.5 0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V
CC
. V
EE
can vary +0.8 V / −0.5 V.
2. Outputs are terminated through a 50 ohm resistor to V
CC
− 2.0 V.
3. V
IHCMR
min varies 1:1 with V
EE
, V
IHCMR
max varies 1:1 with V
CC
. The V
IHCMR
range is referenced to the most positive side of the differential input
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between V
PP
min and 1 V.
