REV. B–10–
ADG528A/ADG529A
TERMINOLOGY
R
ON
Ohmic resistance between terminals D and S
R
ON
Match Difference between the RON of any two channels
R
ON
Drift Change in RON versus temperature
I
S
(OFF) Source terminal leakage current when the switch
is off.
I
D
(OFF) Drain terminal leakage current when the switch is
off.
I
D
(ON) Leakage current that flows from the closed switch
into the body.
V
S
(V
D
)Analog voltage on terminal S or D
C
S
(OFF) Channel input capacitance for “OFF” condition
C
D
(OFF) Channel output capacitance for “OFF” condition
C
IN
Digital input capacitance
t
ON
(EN) Delay time between the 50% and 90% points of
the digital input and switch “ON” condition.
t
OFF
(EN) Delay time between the 50% and 10% points of
the digital input and switch “OFF” condition
t
TRANSITION
Delay time between the 50% and 90% points of
the digital inputs and switch “ON” condition
when switching from one address state to another.
t
OPEN
“OFF” time measured between 50% points of
both switches when switching from one address
state to another
V
INL
Maximum input voltage for Logic “0”
V
INH
Minimum input voltage for Logic “1”
I
INL
(I
INH
) Input current of the digital input
V
DD
Most positive voltage supply
V
SS
Most negative voltage supply
I
DD
Positive supply current
I
SS
Negative supply current
OUTLINE DIMENSIONS
18-Lead Plastic Dual In-Line Package [PDIP]
(N-18)
Dimensions shown in inches and (millimeters)
SEATING
PLANE
0.015 (0.38) MIN
0.180 (4.57)
MAX
0.022 (0.558)
0.014 (0.356)
0.150 (3.81)
0.110 (2.79)
0.100
(2.54)
BSC
0.060 (1.52)
0.045 (1.14)
18
1
9
10
0.885 (22.48)
0.845 (21.46)
0.295 (7.49)
0.275 (6.99)
0.015 (0.381)
0.008 (0.203)
0.325 (8.26)
0.300 (7.62)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
COMPLIANT TO JEDEC STANDARDS MO-095AD
0.180 (4.57)
MAX
20-Lead Plastic Leaded Chip Carrier [PLCC]
(P-20A)
Dimensions shown in inches and (millimeters)
0.020 (0.50)
R
BOTTOM
VIEW
(PINS UP)
0.021 (0.53)
0.013 (0.33)
0.330 (8.38)
0.290 (7.37)
0.032 (0.81)
0.026 (0.66)
0.056 (1.42)
0.042 (1.07)
0.20 (0.51)
MIN
0.120 (3.04)
0.090 (2.29)
3
4
19
18
8
9
14
13
TOP VIEW
(PINS DOWN)
0.395 (10.02)
0.385 (9.78)
SQ
0.356 (9.04)
0.350 (8.89)
SQ
0.048 (1.21)
0.042 (1.07)
0.048 (1.21)
0.042 (1.07)
0.020
(0.50)
R
0.050
(1.27)
BSC
0.180 (4.57)
0.165 (4.19)
0.040 (1.01)
0.025 (0.64)
R
COMPLIANT TO JEDEC STANDARDS MO-047AA
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
